A06_Specifications_1.docx

Okefenokee & Merritt Island Amphibious Tracked Equipment

BODY:

· Approximate dimensions: 15’6” - 17’ long x 8’- 9’ wide x 8’ - 8’8” high

· All Welded 1/8” aluminum body with 3/16” high strength pontoon bottoms

· 6900 - 8000 LB (approx.)

· Minimum 1300 lb. floating load capacity

· Tilt out windshield

· Brush guard on front of machine

· Walking deck full width of the tracks with slip resistant coating on decks (Line X or comparable)

· Minimum 30” ground clearance

· All stainless-steel fasteners throughout machine

· Easily accessible and serviceable 25-30 gallon secured aluminum fuel tank mounted in rear bed area

· Rear mounted hydraulic three-point hitch with quick attach system

· Overhead cargo rack capable of supporting 100 lb. of gear

· Catwalk over winch

· (2) plugs installed in the floorboard of the driver and passenger floorboard for drain purpose

· (1) bottom/floor drain plug in the back cargo area of the machine

· (2) doors installed with removable screens

· (1) back up camera installed

CAB:

· Seating for two people

· Winch control or remote plug locate in cab

· Actuator for pump (fire suppression package) located in cab

· Drive controls operational from either seat

· Minimum required gauges:

· Tachometer

· Engine oil pressure

· Engine temperature

· Hydraulic temperature

· Voltmeter

· Hour meter

· Water level indicator for fire suppression package

DRIVE SYSTEM:

· 70 - 115 HP diesel engine

· TIER 4 FINAL CERTIFIED MEETING ALL REQUIREMENTS SET FORTH BY THE EPA FOR 2019 OFF ROAD DIESEL ENGINES

· Twin Hydrostatic Transmission

· Oil bath lubricated low speed/high torque final drives that requires no external greasing of bearings

· Thermostatic controlled hydraulic driven cooling fan with reversing feature for radiator/oil cooler cleanout

· Side by side radiator/hydraulic oil cooler

· Maintenance free, DOC only, no DEF, no DPF, no REGEN

SPEED:

· 6-8 mph on land, 1 mph in water

TRACK SYSTEM:

· 28” wide aluminum cleats

· Two low stretch rubber belts per track

· Bolt on bogey wheel design for easy replacement

· Four drive sprockets per track (4" pitch)

· Approximately 1 PSI ground pressure

· Bogey axle assemblies must include internal oil bath, lubricated and sealed requiring no external greasing.

· All corrosion-proof stainless-steel track bolts and hardware for saltwater usage

· No external grease points anywhere on rear drive or bogey system

· Front idler shafts and rear drive shafts to be stainless steel. Bearing housings anodized aluminum.

ELECTRICAL SYSTEM:

· 12-volt battery secured in enclosed compartment

· Multifunction engine display

· 2 LED front lights/2 LED rear lights

· 12-volt auxiliary receptacle in cab and rear bed area

· Battery shut-off switch

· Prewired auxiliary switch located on control panel in cab, used for emergency lighting

WINCH and JACK:

· Front Mounted 10,000lb Hydraulic Winch with 135' of 3/8" cable

· Minimum 75’ of wire rope on winch

· Front porthole window allowing operator to see winch cable while winching

· Weight rated jack to lift the machine

FIRE SUPPRESSION SYSTEM

· (2) – 55-gallon aluminum water tank built into each pontoon

· Water level gauge for tanks (Mounted in cab)

· Hydraulic motor driven, self-priming centrifugal water pump

· 15’ of 1 ½” suction hose for quick fill from ditch or lake

· 12’ of 1 ½” discharge hose

· 25’ of 1 ½” discharge hose

· Fog & stream brass spray nozzle

· Camlock hose connections and caps for pump

LOW FLOW AND HIGH FLOW AUXILIARY HYDRAULIC CIRCUITS:

· Low flow auxiliary hydraulic circuit 3-8gpm@3000psi and 2000 rpm

· High flow auxiliary hydraulic circuit 30 GPM max @ 3500 psi/2600 rpm

ROTARY CUTTER SPECIFICATIONS

· Cutting Width: 75 - 80”

· Cutting Capacity: 2" diameter material

· Cutting Heads: Two (2) 38” diameter

· Blades: Two (2) per cutting head; 1/2” x 3” x 11 1/2” heat treated steel

· Spindle Speed: Approx. 1400rpm

· Blade Tip Speed: Approx. 17,000 fpm

· Drive Motors: Two (2), 1 per cutting head, rated @ 50 hp max power input

· Spindles: Two (2) extra heavy duty roller bearings; Spindle Seals well protected from wrap up, grease lubricated

· Deck: Minimum 1/4” thick 5086 Aluminum, with 3/8” thick 6061-T6 Aluminum pivot mounts and side slider frame

· Heavy duty height adjustable skis for supporting cutter deck. Replaceable wear pads on ski bottoms

· Weight: approx.700 pounds

· Tilt & Lift System: Front and rear cutter 3-point hitch, hydraulic with mechanical controls

· Attachment: Quick connect hydraulic hoses, quick-attach pull frame

· Safety Features:

· Auto Shutdown when cutter head is tilted up

· Foot switch at operator seat in cab must be depressed to power cutter head

· Push/pull dash mounted switch to engage cutter.

· Built in hydraulic blade brake that stops blades from free spinning after shutdown

MACHINE/ENGINE WARRANTY:

· Factory Direct

· 1 Year/1000 hr. bumper to bumper whichever comes first

· Engine warranty 3yr/2000 hr. 100% parts and labor

For: Okefenokee National Wildlife, GA

TRAILER SPECIFICATIONS:

· Tilt deck trailer with raised center to prevent slide off while loading and unloading

· Galvanized finish – no rusted frame for the life of the trailer

· Gravity-tilt with hydraulic dampening. No battery or auxiliary hydraulic power unit for tilting.

· The top deck will tilt smoothly to create a ramp to the ground once the buggy passes the pivot point.

· Trailer mounted ladder, for safe access to machine while loaded on trailer

· Center hump guides the buggy and ensures that it stays in the middle of the trailer.

· Maintenance-free torsion axles

· Electric brakes

· Electric brake actuator with breakaway

· 2 5/16” forged adjustable coupler

· Matching spare tire and rim, mounted on trailer

· Minimum GVWR of 13,000 lbs.

· Tongue jack sufficiently strong to allow trailer to be disconnected with fully loaded machine left on it.

· Gravity tilt with hydraulic cylinder dampener

· Four (4) D-ring tie downs

· Two galvanized safety chains per DOT specs

· Light package must include LED lighting system

· Reflector package with (4) 2” red and (2) 2” amber and reflective tape side and rear per DOT standards

· Round 7 blade RV trailer wire connector

· Carrying capacity – 9,300

For Merritt Island National Wildlife Refuge, FL

TRAILER SPECIFICATIONS:

· Tilt deck trailer with raised center to prevent slide off while loading and unloading

· Galvanized finish – no rusted frame for the life of the trailer

· Gravity-tilt with hydraulic dampening. No battery or auxiliary hydraulic power unit for tilting.

· The deckover will tilt smoothly to create a ramp to the ground once the buggy passes the pivot point.

· Trailer mounted ladder, for safe access to machine while loaded on trailer

· Center hump guides the buggy and ensures that it stays in the middle of the trailer

· 4’ fixed deck in front of the tilt deck for multiple attachment transport

· Maintenance-free torsion axles

· Electric brakes

· Electric brake actuator with breakaway

· 2 5/16” forged adjustable coupler

· Matching spare tire and rim, mounted on trailer

· Minimum GVWR of 13,000 lbs.

· Tongue jack sufficiently strong to allow trailer to be disconnected with fully loaded machine left on it.

· Gravity tilt with hydraulic cylinder dampener

· Four (4) D-ring tie downs

· Two galvanized safety chains per DOT specs

· Light package must include LED lighting system

· Reflector package with (4) 2” red and (2) 2” amber and reflective tape side and rear per DOT standards

· Round 7 blade RV trailer wire connector

· Carrying capacity – 9,300

DELIVERY LOCATIONS:

1) Okefenokee National Wildlife Refuge (NWR), 4155 Suwannee Canal Road, Folkston, GA 31537

2) Merritt Island NWR 1987 Scrub Jay Way #32782, Titusville, FL 32782Titusville, FL.