Solicitation 0407.rtf

file_0.wmf

552.219-71 NOTICE TO OFFERORS OF SUBCONTRACTING PLAN REQUIREMENTS (JUN 2005)

The General Services Administration (GSA) is committed to assuring that maximum practicable opportunity is provided to small, HUB Zone small, small disadvantaged, women-owned, veteran-owned, and service-disabled veteran owned small business concerns to participate in the performance of this contract consistent with its efficient performance. GSA expects any subcontracting plan submitted pursuant to FAR 52.219-9, Small Business Subcontracting Plan, to reflect this commitment. Consequently, an offeror, other than a small business concern, before being awarded a contract exceeding $550,000 ($1,000,000 for construction), must demonstrate that its subcontracting plan represents a creative and innovative program for involving small, HUB Zone small, small disadvantaged, women-owned, veteran-owned, and service-disabled veteran owned small business concerns as subcontractors in the performance of this contract.

CP-FSS-1-A (APR 1993)

6FLS-K2-090407-N

STOCK REQUIREMENTS CONTRACT FOR

FSC 8010 – Miscellaneous Items PERIOD: 5/1/2010, or date of award, whichever is later, through 4/30/2012 With Three 1-year Options

6FLS-CP-FSS-17 PAST PERFORMANCE EVALUATION FACTOR (FEB 2007)

Federal Acquisition Regulation (FAR) Chapter 15.3 requires that past performance be an evaluation factor in competitively negotiated contracts over $100,000. However, FAR 15.304(c)(3)(iii) states “Past performance need not be evaluated if the contracting officer documents the reason past performance is not an appropriate evaluation factor for the acquisition.” Past performance may be used as a factor in solicitations under $100,000 at the discretion the Contracting Officer. Offerors are advised that the quality of an offeror’s past performance, on contracts similar to that solicited, will be a factor in the award decision for this solicitation. Further, the Contractor’s performance under any contract(s) resulting from this solicitation may directly impact future contract awards. Past Performance will be one of the significant factors used in the Lowest Price Technically Acceptable (LPTA) process as indicated above in CP-FSS-2 – Significant changes.

CP-FSS-2 SIGNIFICANT CHANGES (OCT 1988)

The attention of offeror is invited to the following changes made since the issuance of the last solicitation for the supplies/services covered herein:

Vendor Checklist Fill-in Self Certification Past Performance Questionnaire Charges for Marking in Clause 552.211-74 Charges for Packaging and Packing in Clause 552.211-76

CP-FSS-3 NOTICE: REQUESTS FOR EXPLANATION OR INFORMATION (MAR 1996)

Oral or written requests for explanation or information regarding this solicitation should be directed to:

GENERAL SERVICES ADMINISTRATION

GSA Heartland Global Supply (QSDKAB-F7) 1500 East Bannister Road, Atrium Kansas City, MO 64131 or Phone: Margaret Conroy @ 816/823-1284 IMPORTANT: DO NOT ADDRESS OFFERS, MODIFICATIONS OR WITHDRAWALS TO THE ABOVE ADDRESS. THE ADDRESS DESIGNATED FOR RECEIPT OF OFFERS IS CONTAINED ELSEWHERE IN THIS SOLICITATION.

CP-FSS-6 ELECTRONIC DATA INTERCHANGE (EDI) ORDERING (JAN 1994)

Offerors are advised that the Federal Supply Service is expanding use of electronic communications to exchange business documents. The Placement of Orders clause contained in this contract provides that orders may be placed using Electronic Data Interchange (EDI) procedures.

General Services Administration 1500 East Bannister Road Kansas City, MO 64131

SPECIAL INSTRUCTIONS:

The use of a manufacturer’s part number or brand name, when shown in an item description in this solicitation, appears in the description based on our record of current certifications (QPL) of manufacturer’s products that are QPL certified to meet the specification. Identification of one or more manufacturer’s part numbers or brand name references herein, or the omission of any other manufacturer’s product, is not meant to exclude any currently certified manufacturer’s part numbers or items not listed, from consideration. Parties interested in submitting an offer for part numbers or brand names not listed in a specification, should include a copy of a valid QPL certification for each item they wish consideration, showing that their product has been certified to meet the specification. The acquisition office is not a testing facility. The acquisition office recognizes only QPL certified products as meeting the specification. Offers for a product that is not listed in the specification which do not include a valid QPL certification will not receive consideration. To receive consideration, items must have been certified by QPL prior to bid opening.

THE DESCRIPTIONS LISTED IN THIS SOLICITATION MAY CONTAIN ONE OR MORE OF THE FOLLOWING DOCUMENTS. IF ANY ARE NEEDED, PLEASE REQUEST THEM BY CALLING THE PHONE NUMBERS OR WRITING TO THE ADDRESSES LISTED.

ANSI STANDARDS

AMERICAN NATIONAL STANDARDS INSTITUTE, INC.

11 West 42nd Street, 13th Floor New York, NY 10036 (Tel. #: 212/642-4900)

ASTM

AMERICAN SOCIETY FOR TESTING AND MATERIAL

100 Barr Harbor Drive West Conshoshocken, PA 19428-2959 (Tel. #: 215/299-5400)

MILITARY SPECIFICATIONS/STANDARDS

Department of Defense Single Stock Point (DoDSSP) Bldg. #4, Section D 700 Robbins Avenue Philadelphia, PA 19111-5094 (Tel. #: 215/697-2667 & 215/697-2179) (Facsimile #: 215/697-1462) DoDSSP Internet Address: http://www.dodssp.daps.mil

ASC

AMERICAN SOCIETY FOR QUALITY

Post Office Box 3005 Milwaukee, WI 53201-3005 Or 600 North Plankinton Ave Milwaukee, WI 53203 Tel. #: 800-248-1946 FAX 414/272-1734

FEDERAL SPECIFICATIONS/STANDARDS & COMMERCIAL ITEM DESCRIPTIONS

General Services Administration Federal Supply Service, Specifications Section 470 East L'Enfant Plaza, SW, Ste. #8100 Washington, DC 20407 (Tel. #: 202/619-8925)

(FAX #: 202/619-8978)

ASME

AMERICAN SOCIETY OF MECHANICAL ENGINEERS

345 East 47th Street New York, NY 10017 (Tel. #: 1-800-843-2763)

National Aerospace Standards Aerospace Industries Association of America 1725 De Sales Street, N.W.

Washington, DC 20036

MPI

MASTER PAINTS INSTITUTE

4090 Gravely Street Burnaby, BC V5C3T6 ((Tel.# 604/298-7578 contact: Bob Welch) http://www.paintinfo.com/

ISO

International Organization for standardization

WWW.ISO.CH

CP-FSS-4-A SOLICITATION COPIES (MAR 1996)

(a) To reduce Government costs, only one copy (either paper copy or diskette) of this solicitation is provided to addressees on our bidders' mailing list. If additional paper copies are required (see52.2121, Instructions to Offerors Commercial Items and its addendum for number of copies to be submitted), you may reproduce them yourself, provided they are complete in every respect*, or you may obtain them from the address specified below:

General Services Administration 1500 E. Bannister Road Kansas City, MO 64131

Phone: 816-823-1284

(b) Offerors are strongly urged to use two sided copying of offers for submission to GSA.

* EXCEPTION: Oversized blueprints, drawings, or similar documents which are incorporated by reference in and attached (folded) to the solicitation are not required to be duplicated for the purpose of submitting a duplicate copy of the offer to GSA.

CP-FSS-30 (APR 1993)

PLEASE REMOVE THIS COVER PAGE(S) BEFORE SUBMITTING OFFER TO GSA.

6FLS-K2-090407-N

Vendor Checklist - Did I remember to…..

_____ Complete required fields of SF 1449

_____ Sign and Date SF 1449

_____ Complete and return attachments:

Self Certification/Acknowledgement of Past Performance Questionnaire Form

_____ Include MSDS as required

_____ Complete ALL applicable Fill-in clauses, provisions

_____ Return signed amendments (if applicable)

_____ Read 52.212-2, Evaluation of Commercial Items, for details on evaluation plan

SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL ITEMS

1. REQUISITION NUMBER

Offeror to complete blocks 12, 17, 23, 24, & 30

2. CONTRACT NO.

3. AWARD/EFFECTIVE DATE

4. ORDER NUMBER

5. SOLICITATION NUMBER

6. SOLICITATION ISSUE DATE

6FLS-K2-090407-N

1/14/2010

7. FOR SOLICITATION

A. NAME

B. TELEPHONE NUMBER (No Collect Calls)

8. OFFER DUE DATE/local time LOCAL TIME

INFORMATION CALL:

Margaret Conroy 816/823-1284 2/12/2010-2:00 pm cst ccccst

9. ISSUED BY

CODE

10. THIS ACQUISITION IS

11. DELIVERY FOR FOB

DESTINATION UNLESS

12. DISCOUNT TERMS

General Services Administration

X UNRESTRICTED Items 2, 3, 4, 7, 9, 10, 11, 12, 13, 14, 15, 16, 17 and 18

BLOCK IS MARKED

SEE SCHEDULE

Office of Business & Support Services (6ADB) – Room 1161

X SET-ASIDE Items: 2, 5 and 6.

2 % FOR

13a. THIS CONTRACT IS A RATED ORDER 1500 East Bannister Rd

X SMALL BUSINESS #27&42

UNDER DPAS (15 CFR 700)

Kansas City, MO 64131

HUBZONE SM. BUSINESS BUSINSESS

13b. RATING 8(A) ADDRESS OFFERS TO: SAME ADDRESS AS ABOVE (No Faxes)

NAICS:325510

14. METHOD OF SOLICITATION

SIZE STANDARD:500

RFQ IFB XRFP

15. DELIVER TO

CODE

16. ADMINISTERED BY

CODE

To be shown on each order issued under any contract resulting from th this solicitation.

GSA/FAS/QVOCBA

Contract Management Division, MS 34-3 230 South Dearborn Street, Room 3486 Chicago, IL 60604 17a. CONTRACTOR/OFFEROR

OFFEROR

CODE

FACILITY CODE

18a. PAYMENT WILL BE MADE BY

CODE

To be shown on each order issued under any contract resulting from this solicitation.

TELEPHONE NO.

18b. SUBMIT INVOICES TO ADDRESS SHOWN IN BLOCK 18a UNLESS BLOCK BELOW IS CHECKED:

17b. CHECK IF REMITTANCE IS DIFFERENT AND PUT SUCH ADDRESS IN OFFER

SEE ADDENDUM

19., 20.

21.

22.

23.

24.

ITEM NO

SCHEDULE OF SUPPLIES/SERVICES

QUANTITY

UNIT

UNIT PRICE

AMOUNT

See Schedule of Items beginning on page 2.

(Attach Additional Sheet as Necessary)

25. ACCOUNTING AND APPROPRIATION DATA

26. TOTAL AWARD AMOUNT (For Govt.Use Only) See block 15 Indefinite 27a. solicitation incorporates by reference FAR 52.212-1, 52.212-4. FAR 52.212-3 and 52.212-5 are attached. Addenda are are not attached.

27b. contract/purchase order incorporates by reference FAR 52.212-4. FAR 52.212-5 are attached. Addenda are are not attached.

28.

X CONTRACTOR IS REQUIRED TO SIGN THIS DOCUMENT AND RETURN 1 COPIES TO ISSUING OFFICE. CONTRACTOR AGREES TO FURNISH AND DELIVER ALL ITEMS SET FORTH OR OTHERWISE IDENTIFIED ABOVE AND ON ANY ADDITIONAL SHEETS SUBJECT TO THE TERMS AND CONDITIONS SPECIFIED HEREIN.

29.

AWARD OF CONTRACT: REFERENCE OFFER DATED . YOUR OFFER ON SOLICITATION (BLOCK 5), INCLUDING ANY ADDITIONS OR CHANGES WHICH ARE SET FORTH HEREIN, IS ACCEPTED AS TO ITEMS:

30a. SIGNATURE OF OFFEROR/CONTRACTOR 31a. UNITED STATES OF AMERICA (SIGNATURE OF CONTRACTING OFFICER)

30b. NAME AND TITLE OF SIGNER (TYPE OR PRINT) 30c. DATE SIGNED 31b. NAME OF CONTRACTING OFFICER (TYPE OR PRINT) 31c. DATE SIGNED

MARGARET CONROY

19., 20.

21.

22.

23.

24.

ITEM NO

SCHEDULE OF SUPPLIES/SERVICES

QUANTITY

UNIT

UNIT PRICE

AMOUNT

32a. QUANTITY IN COLUMN 21 HAS BEEN

RECEIVED INSPECTED ACCEPTED, AND CONFORMS TO THE CONTRACT EXCEPT AS NOTED:

32b. SIGNATURE OF AUTHORIZED GOVERNMENT REPRESENTATIVE 32c. DATE 32d. PRINTED NAME AND TITLE OF AUTHORIZED GOVERNMENT REPRESENTATIVE 32e. MAILING ADDRESS OF AUTHORIZED GOVERNMENT REPRESENTATIVE 32f. TELEPHONE NUMBER OF AUTHORIZED GOVERNMENT REPRESENTATIVE

32g. E-MAIL OF AUTHORIZED GOVERNMENT REPRESENTATIVE

33. SHIP NUMBER

PARTIAL FINAL

34. VOUCHER NUMBER

35. AMOUNT VERIFIED CORRECT FOR

36. PAYMENT

COMPLETE PARTIAL FINAL

37. CHECK NUMBER

38. S/R ACCOUNT NUMBER

39. S/R VOUCHER NUMBER

40. PAID BY

41a. I CERTIFY THIS ACCOUNT IS CORRECT AND PROPER FOR PAYMENT 42a. RECEIVED BY (Print) 41b. SIGNATURE AND TITLE OF CERTIFYING OFFICER 41c. DATE

42b. RECEIVED AT (Location)

42c. DATE REC’D (YY/MM/DD) 42d. TOTAL CONTAINERS

STANDARD FORM 1449 (REV. 3/2005) BACK6FLS-K2-090407-N 61 of 72

6FLS-K2-090407-N 2 of 72

SCHEDULE OF ITEMS

Unit of Est. 2-yr Issue Depot Quantity Minimum EPMR Price

1. 8010-01-060-7176 KT Burlington, NJ 240 1 70 $ __________

REPAIR KIT, EPOXY

DESCRIPTION

Used to repair M149 Trailer Tanks. In accordance with U.S. Army TACOM Drawing 12259529, dated 2/8/1977, revised 12/7/1978.

See Technical Specifications paragraph(s): T1.3 and T6.1.

2. 8010-01-348-3060 PT Burlington, NJ 1626 12 1626 $ __________

French Camp, CA 456 12 456 $ __________

ENAMEL

DESCRIPTION

Use: General purpose aerosol enamel

Type 1: Solvent thinned enamel

Color: Gray in accordance with the latest version of FED-STD-595, color number 36118.

Size: Aerosol can, minimum net wt. 11 oz. (311 g)

Shelf Life Code 7: Age on delivery shall not exceed 6 months.

Date of reinspection shall be 36 months from date of manufacture.

See Technical Specifications paragraph(s): T1.1, T3.1, T4.4, T5.3 and T6.1.

3. 8010-01-419-1163 KT Burlington, NJ 100 2 47 $ __________

EPOXY COATING KIT

DESCRIPTION

Use: Topcoat for aircraft and ground support equipment, lead-free.

Color: Gray in accordance with the latest version of FED-STD-595, color number 16440.

Size: Kit, consists of components A and B to produce 1.89 liters (2 quarts).

Shelf Life Code 6: Age on delivery shall not exceed 4 months.

Date of reinspection shall be 24 months from date of manufacture.

See Technical Specifications paragraph(s): T1.5, T3.2, T4.3, T5.1 and T6.1.

Unit of Est. 2-yr Issue Depot Quantity Minimum EPMR Price

4. 8010-01-441-5927 GL Burlington, NJ 1684 4 487 $ __________

ENAMEL

DESCRIPTION

Use: For interior plaster, gypsum wallboard, wood and metal doors, and trim.

Color: Beige in accordance with the latest version of FED-STD-595, color number 27778.

Size: 3.79 Liters (1 gallon)

Shelf Life Code 6: Age on delivery shall not exceed 4 months.

Date of reinspection shall be 24 months after date of manufacture.

See Technical Specifications paragraph(s): T1.7, T2.1, T3.1, T4.2, T5.2 and T6.1.

Unit of Est. 2-yr Issue Depot Quantity Minimum EPMR Price

5. 8010-01-441-5940 GL Burlington, NJ 1728 6 400 $ __________

French Camp, CA 2004 6 400 $ __________

THINNER, PAINT PRODUCTS

DESCRIPTION

Use: For reducing the viscosity of medium oil and styrenated alkyd resin enamels. It can also be used for phenol formaldehyde spar varnishes.

Size: 3.79 Liters (1 gallon)

Shelf Life Code 7. Age on delivery shall not exceed 5 months.

Date of reinspection shall be 36 months from date of manufacture.

See Technical Specifications paragraph(s): T1.2, T3.1, T4.5, T5.4 and T6.1.

Unit of Est. 2-yr Issue Depot Quantity Minimum EPMR Price

6. 8010-01-441-5941 CN Burlington, NJ 443 1 200 $ __________

French Camp, CA 396 1 200 $ __________

THINNER, PAINT PRODUCTS

DESCRIPTION

Use: For reducing the viscosity of medium oil and styrenated alkyd resin enamels. It can also be used for phenol formaldehyde spar varnishes.

Size: 18.9 Liters (5 gallon)

Shelf Life Code 7. Age on delivery shall not exceed 5 months.

Date of reinspection shall be 36 months from date of manufacture.

See Technical Specifications paragraph(s): T1.2, T3.1, T4.1 and T6.1.

7. 8010-00-292-1127 GL Burlington, NJ 980 24 495 $ __________

French Camp, CA 1032 24 537 $ __________

PRIMER COATING

DESCRIPTION

Use: Zinc Oxide, Alkyd, Linseed Oil Primer for use over hand cleaned steel.

Color: Red-Brown

Size: 3.79 liter (1 gallon)

Shelf Life Code 6. Age on delivery shall not exceed 4 months.

Date of reinspection shall be 24 months from date of manufacture.

See Technical Specifications paragraph(s): T1.8, T3.1, T4.2, T5.2 and T6.1.

8. 8010-01-302-3606 KT Burlington, NJ 90 1 10 $ __________

French Camp, CA 78 1 10 $ __________

EPOXY COATING KIT

DESCRIPTION

Use: For exterior hull surfaces, use on sandblasted steel, aluminum or fiberglass.

Specification Sheet: MIL-DTL-24441/22A, dated 19 May 1999 Type 3: Three coat system, max VOC 340 g/l.

Formula 152

Color: White, in accordance with the latest version of FED-STD-595, color number 27886.

Size: Kit, consists of equal parts of components A and B to equal 37.9 liters (10 gallons).

Shelf Life Code 6: Age on delivery shall not exceed 4 months.

See Technical Specifications paragraph(s): TE.1, TE.6, T1.4, T3.2, T4.3, T5.1 and T6.1.

9. 8010-01-302-3607 KT Burlington, NJ 214 1 89 $ __________

French Camp, CA 136 1 13 $ __________

EPOXY COATING KIT

DESCRIPTION

Use: For exterior hull surfaces, use on sandblasted steel, aluminum or fiberglass.

Specification Sheet: MIL-DTL-24441/26A, dated 19 May 1999 Type 3: Three coat system, max VOC 340 g/l.

Formula 156

Color: Red in accordance with the latest version of FED-STD-595, color number 20152.

Size: Kit, consists of equal parts of components A and B to equal 37.9 liters (10 gallons).

Shelf Life Code 6: Age on delivery shall not exceed 4 months.

10. 8010-01-302-3608 KT Burlington, NJ 1550 1 729 $ __________

French Camp, CA 1584 1 783 $ __________

EPOXY COATING KIT

DESCRIPTION

Use: For exterior hull surfaces, use on sandblasted steel, aluminum or fiberglass.

Specification Sheet: MIL-DTL-24441/20A, dated 19 May 1999 Type 3: Three coat system, max VOC 340 g/l.

Formula 150

Color: Green in accordance with the latest version of FED-STD-595, color number 24272.

Size: Kit, consists of equal parts of components A and B to equal 37.9 liters (10 gallons).

Shelf Life Code 6: Age on delivery shall not exceed 4 months.

11. 8010-01-302-6838 KT Burlington, NJ 260 2 107 $ __________

French Camp, CA 86 2 11 $ __________

EPOXY COATING KIT

DESCRIPTION

Use: For exterior hull surfaces, use on sandblasted steel, aluminum or fiberglass.

Specification Sheet: MIL-DTL-24441/21A, dated 19 May 1999 Type 3: Three coat system, max VOC 340 g/l.

Formula 151

Color: Gray in accordance with the latest version of FED-STD-595, color number 26270.

Size: Kit, consists of equal parts of components A and B to equal 37.9 liters (10 gallons).

Shelf Life Code 6: Age on delivery shall not exceed 4 months.

12. 8010-01-347-0916 KT Burlington, NJ 530 5 269 $ __________

French Camp, CA 123 5 52 $ __________

EPOXY COATING KIT

DESCRIPTION

Use: For exterior hull surfaces, use on sandblasted steel, aluminum or fiberglass.

Specification Sheet: MIL-DTL-24441/20A, dated 19 May 1999 Type 3: Three coat system, max VOC 340 g/l.

Formula: 150

Color: Green in accordance with the latest version of FED-STD-595, color number 24272.

Size: Kit, consists of equal parts of components A and B to equal 1.89 liters (2 quarts).

Shelf Life Code 6: Age on delivery shall not exceed 4 months.

13. 8010-01-350-4741 KT Burlington, NJ 910 5 68 $ __________

French Camp, CA 1200 5 104 $ __________

EPOXY COATING KIT

DESCRIPTION

Use: For exterior hull surfaces, use on sandblasted steel, aluminum or fiberglass.

Specification Sheet: MIL-DTL-24441/21A, dated 19 May 1999 Type 3: Three coat system, max VOC 340 g/l.

Formula 151

Color: Gray in accordance with the latest version of FED-STD-595, color number 26270.

Size: Kit, consists of equal parts of components A and B to equal 7.57 liters (2 gallons).

Shelf Life Code 6: Age on delivery shall not exceed 4 months.

14. 8010-01-350-4742 KT Burlington, NJ 2033 25 149 $ __________

French Camp, CA 1717 25 138 $ __________

EPOXY COATING KIT

DESCRIPTION

Use: For exterior hull surfaces, use on sandblasted steel, aluminum or fiberglass.

Specification Sheet: MIL-DTL-24441/20A, dated 19 May 1999 Type 3: Three coat system, max VOC 340 g/l.

Formula 150

Color: Green in accordance with the latest version of FED-STD-595, color number 24272.

Size: Kit, consists of equal parts of components A and B to equal 7.57 liters (2 gallons).

Shelf Life Code 6: Age on delivery shall not exceed 4 months.

15. 8010-01-350-4743 KT Burlington, NJ 221 5 35 $ __________

French Camp, CA 413 5 48 $ __________

EPOXY COATING KIT

DESCRIPTION

Use: For exterior hull surfaces, use on sandblasted steel, aluminum or fiberglass.

Specification Sheet: MIL-DTL-24441/22A, dated 19 May 1999 Type 3: Three coat system, max VOC 340 g/l.

Formula 152

Color: White, in accordance with the latest version of FED-STD-595, color number 27886.

Size: Kit, consists of equal parts of components A and B to equal 7.57 liters (2 gallons).

Shelf Life Code 6: Age on delivery shall not exceed 4 months.

16. 8010-01-350-4745 KT Burlington, NJ 213 5 29 $ __________

French Camp, CA 177 5 32 $ __________

EPOXY COATING KIT

DESCRIPTION

Use: For exterior hull surfaces, use on sandblasted steel, aluminum or fiberglass.

Specification Sheet: MIL-DTL-24441/26A, dated 19 May 1999 Type 3: Three coat system, max VOC 340 g/l.

Formula 156

Color: Red, in accordance with the latest version of FED-STD-595, color number 20152.

Size: Kit, consists of equal parts of components A and B to equal 7.57 liters (2 gallons).

Shelf Life Code 6: Age on delivery shall not exceed 4 months.

See Technical Specifications paragraph(s): TE.1, T1.4, T3.2, T4.3, T5.1 and T6.1.

TECHNICAL SPECIFICATIONS

TECHNICAL DOCUMENT

T1.1

In accordance with Commercial Item Description A-A-2787, dated February 26, 1992.

Applies to item(s) : 2.

T1.2

In accordance with Commercial Item Description A-A-3007, dated July 16, 1996.

Applies to item(s) : 5 and 6.

T1.3

Use: To repair M149 trailer tanks

Size: Kit contains steel wire and fiberglass reinforcing material, 250 ml polyester body filler, 750 ml epoxy resin, polyurethane foam, silica, white pigment and accessories.

In accordance with U.S. Army Tank and Automotive Command Specification Control Drawing Part Number 12259529, dated August 2, 1977, letter A revision December 7, 1978, and the Exceptions listed below.

COMPONENT 2: Delete "P970-75 or equal. MIL-C-9084 Class II, Type 12 or 12A."

NOTE: MIL-C-9084 cancelled 10 Sep 99, S/S by SAE-AMS9084

COMPONENT 3: Delete "0.030" and replace with "0.080." Delete "MIL-W-360" NOTE: MIL-W-360 changed to WW-R-360, cancelled 10 Sep 99, S/S by A-A-1037, canceled 10 Jan 94, S/S by ANSI/AWCI-01-1992.

COMPONENT 4: Delete "MIL-47129" or MIL-47129. Add "or Cab-O-Sil M5."

NOTE: MIL-S-14760 cancelled 4 Feb 03, no S/S document. MIL-47129 may be MIL-S-47129, cancelled 25 Apr 96, SS by SAE-AMS 3755

COMPONENT 5: Before "1/2 in." add "approximately". After "commercial" add "flux and adhesive brush."

COMPONENT 6: Before "1-1/2" in." add "approximately." After "commercial" add "chip brush, such as EZ Paint product number 70042-50010, Adams Brush MFG. Co., Inc. product number US42315, American Brush product number 000502 or equal."

COMPONENT 7: Delete "Fed Spec GG-D-226" and replace with "Made of close grained hard wood, approximately 5-3/4 inches long, 11/16 inch wide, and 1/16 inch thick."

NOTE: GG-D-226 cancelled 15 Oct 90, S/S by A-A-30041, cancelled 22 Nov 00, no S/S document.

COMPONENT 8: Delete MIL-P-22035 and replace with L-P-512. L-P-512 cancelled and superseded by either ASTM D 2103, Standard Specification for Polyethylene Film and Sheeting for polyethylene film and sheeting up to 0.3mm (0.012 inch) in thickness inclusive, or ASTM D 4801, Standard Specification for Polyethylene Sheeting in Thickness of 0.25 mm (0.010 inch) and greater for sheeting equal to or greater than 0.25 mm (0.010 inch) are suitable replacements for the polyethylene plastic sheet (sheeting). Users are cautioned to evaluate these documents for their particular application before citing them as replacement documents.

COMPONENT 9: Delete "Grade A, Category A" and replace with "Grade C."

COMPONENT 10: Delete "Ferro VZ 33-30."

COMPONENT 12: Delete "UU-T-591, Type III" and replace with "Approximately 10 X 13 inches, C-fold."

NOTE: UU-T-591 cancelled 23 aug 90, S/S by A-A-696, cancelled 18 Oct 99, no S/S document.

COMPONENT 14: Delete "Long, heavy, weight" and replace with: The gloves shall be 11 to 20 inches long and 0.9 to 1.8 mils thick." After "commercial" add:

"Impermeability shall be determined by the following procedure. The fingers of the glove shall be filled with either isopropyl alcohol or acetone. After the glove is held for two minutes, the outside of the fingers shall be wiped with a clean dry cloth or paper towel. Immediately after the glove is wiped, the cloth or towel shall be visually examined for any wetness due to the solvent. None shall be detected."

COMPONENT 15: Delete "Fed. Spec. GGG-M-125/8, Type II" NOTE: GGG-M-125/8 cancelled 5 Apr 95, no S/S document.

COMPONENT 16: Delete "TT-F-322". Add "Component 16 shall be accepted based on a certificate of compliance in place of testing."

NOTE: TT-F-322 cancelled 28 Nov 97, S/S by A-A-3133.

COMPONENT 17: In place of MIL-R-37252, use Shell Epon 828 or Dow DER 331.

NOTE 2: Delete "Epon U, per publication No, SC: 71-5" and replace with "Epi-Cure 3282." After last line, add the following:

"Ancamine 1483, Pacific Anchor Chemical, Performance Chemical Division, Air Products and Chemicals, Inc."

One (1) kit.

COMPONENT PACKAGING: Individual components of this kit shall be packaged in accordance with Part Number 12259529 and U.S. Army Packaging Data Sheet for Part Number 12259529, Revision B, dated October 1, 1980. Cans shall conform to normal commercial practice and be closed in such a manner as not to spill or leak during transportation, storage, and redistribution. Components 1 and 3 shall be packaged as specified in the Packaging Data Sheet.

KIT PACKAGING: The individual components of this kit, packaged as specified above shall be further packaged as specified in U.S. Army Packaging Data Sheet for Part Number 12259529.

PACKING: The kits, packaged as specified above, shall be further packed in a close-fitting corrugated fiberboard box conforming to Section 6(a), Rule 41 of the Uniform Freight Classification and Item 222 of the National Motor Freight Classification. Closure of the boxes shall be in accordance with Section 7 of Rule 41 of the Uniform Freight Classification. The complete package offered for shipment shall meet all requirements of the Department of Transportation (DOT) and the International Maritime Dangerous Goods Code (IMDG). Gross weight shall not exceed 65 pounds.

MARKING Shall include:

(1) Lot or Batch number

(2) Dates of manufacture and reinspection (36 months)

(3) Marking required by Notes A, B, C of Packaging Data Sheet for Part number 12259529 Revision B, dated October 1, 1980.

Applies to item(s) : 1.

T1.4

In accordance with Military Specification MIL-DTL-24441D, dated August 27, 2009.

QPL QUALIFICATION REQUIRED: QPL transformed to QPD, September 20, 2008. Please go to http://assist.daps.dla.mil/quicksearch/, and follow the steps below to view the QPD.

1. Input "24441" in Document Number field and click "Submit"

2. Click on the primary specification link in "Document ID" column.

3. Click on "Qualification" in the "Overview" section to view the QPD.

Applies to item(s) : 8, 9, 10, 11, 12, 13, 14, 15 and 16.

T1.5

In accordance with Military Specification MIL-PRF-22750F, dated 31 May 1994.

QPL QUALIFICATION REQUIRED: QPL transformed to QPD, September 27, 2007. Please go to http://assist.daps.dla.mil/quicksearch/, and follow the steps below to view the QPD.

1. Input "22750" in Document Number field and click "Submit"

2. Click on the primary specification link in "Document ID" column.

3. Click on "Qualification" in the "Overview" section to view the QPD.

Applies to item(s) : 3.

T1.6

Master Painters Institute Detailed Performance Standard, MPI #47, Interior Alkyd, Semi-Gloss, MPI Gloss level 5, dated June 1, 2002.

Applies to item(s) : 4.

T1.7

The Society for Protective Coatings Paint Specification No. 25, Zinc Oxide, Alkyd, Linseed Oil Primer for Use Over Hand Cleaned Steel Type I and Type II, dated May 1, 1997, editorial changes November 1, 2004.

Applies to item(s) : 7.

EXCEPTION(S) TO TECHNICAL DOCUMENT

T2.1

In accordance with the Uniform Facilities Guide Specifications, UFGS-09900, dated February 2002, Division 09 - Finishes, Section 09900, Paints and Coatings, the Current MPI "Approved Product List" which lists paint by brand, label, product name and product code as of the date of contract award, will be used to determine compliance with the submittal requirements of this specification. No variation from the MPI Approved Products List is acceptable.

URL to determine acceptable Approved Product List:

http://www.specifypaint.com/APL/paintinfo_APL/ProductIdxByMPInum.asp

Applies to item(s) : 4.

ITEM MARKING

T3.1

(1) National Stock Number (NSN).

(2) Specification number (Including type, class, and color number) as applicable.

(3) Manufacturer's name and part number.

(4) Lot and Batch Number.

(5) Date of Manufacture and date of expiration or reinspection (month and year).

(6) Instructions for use.

(7) Storage Instructions.

(8) Maximum Volatile Organic Compound (VOC) Content (less water and exempt solvents) in grams per liter and pounds per gallon.

If applicable, supplier will follow pre-arranged California South Coast labeling requirements.

Applies to item(s) : 2, 4, 5, 6 and 7.

T3.2

(1) National Stock Number (NSN).

(2) Specification number (Including type, class, and color number) as applicable.

(3) Manufacturer's name and part number.

(4) Kit Name and Component Part.

(5) Lot and Batch Number.

(6) Date of Manufacture and date of expiration or reinspection (month and year).

(7) Instructions for use.

(8) Storage Instructions.

Applies to item(s) : 3, 8, 9, 10, 11, 12, 13, 14, 15 and 16.

PACKAGING

T4.1

The product shall be furnished in the specified quantities in new closed head metal shipping pails with closure and handles of the type normally used for this product, providing that there will be no interaction chemically or physically with the contents so as to damage the container or alter the strength, quality or purity of the contents. The filled containers shall be closed and sealed in a manner that will insure the contents will not spill or leak from the containers during shipment, handling, storage and distribution. The containers shall meet the applicable requirements of the National Motor Freight Classification, Uniform Freight Classification and the Department of Transportation regulations.

Applies to item(s) : 6.

T4.2

The product shall be furnished in the units indicated and Performance Oriented Packaged (POP) as follows:

GALLONS AND QUARTS: Material shall be furnished in round containers with multiple friction closure of the type normally used for the product. Filled containers shall be closed in a manner that will insure that the contents will not spill or leak from the container during shipment, handling, storage and redistribution.

PRODUCT CONFORMANCE: The products provided shall meet the salient characteristics of this description, conform to the producer's own specifications, standards, and quality assurance practices and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance.

PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed in accordance with the latest revision of ASTM D 3951, Standard Practice for Commercial Packaging. Copies of ASTM standards are available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. Phone: 610-832-9585, Fax: 610-832-9555, Web site: www.astm.org, e-mail: service@astm.org.

All containers shall be constructed so that there will be no interaction chemically or physically with the contents that damages the container or alters the strength, quality or purity of the contents.

One gallon containers shall be provided with a bail type handle in accordance with current Good Manufacturing Practices.

Material packaged as specified above shall be packed in a close-fitting, corrugated, fiberboard box conforming to Section 6(a), Rule 41 of the Uniform Freight Classification, Item 222 of the National Motor Freight Classification (200 minimum burst). Closure of the boxes shall be in accordance with Section 7 of Rule 41 of the Uniform Freight Classification. Gross weight of the box and contents shall not exceed 65 pounds. Pails shall meet the minimum applicable requirements of the National Motor Freight Classification, Uniform Freight Classification, and the Department of Transportation (49 CFR). For oversea shipments by vessel, the commodity shall be packaged, packed, and marked in a manner to meet the applicable requirements of International Maritime Organization (IMO), International Maritime Dangerous Goods (IMDG) Code, latest revision.

Applies to item(s) : 4 and 7.

T4.3

The components of each kit shall be packaged in multiple friction closure cans in accordance with the supplier's normal commercial practice, provided that there will be no interaction chemically or physically with the contents so as to damage the container or alter the strength, quality, or purity of the contents. The containers shall be closed in a manner that will insure that the contents will not spill or leak from the containers during shipment, handling, storage and redistribution. In addition to other requirements of this description, for domestic shipments, the commodity shall be packaged, packed, and marked in a manner to meet the applicable requirements of the Department of Transportation (DOT) regulations (Title 49, Code of Federal Regulations) latest revision for the mode of transport utilized. For oversea shipments by vessel, the commodity shall be packaged, packed, and marked in a manner to meet the applicable requirements of International Maritime Organization (IMO), International Maritime Dangerous Goods (IMDG) Code, latest revision.

PRODUCT CONFORMANCE: The products provided shall meet the salient characteristics of this description, conform to the producer's own specifications, standards, and quality assurance practices and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance.

PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed in accordance with the latest revision of ASTM D 3951, Standard Practice for Commercial Packaging. Copies of ASTM standards are available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. Phone: 610-832-9585, Fax: 610-832-9555, Web site: www.astm.org, e-mail: service@astm.org.

Applies to item(s) : 3, 8, 9, 10, 11, 12, 13, 14, 15 and 16.

T4.4

The product shall be furnished in the specified quantity in round, compound lined, double seamed end cans with pressure activated spray orifice type dispensers of the type normally used for this product, providing that there will be no interaction chemically or physically with the contents so as to damage the container or alter the strength, quality or purity of the contents. Each can shall be provided with a removable/replaceable metal or full sized, double shell, plastic cap adequate to protect the dispenser in accordance with normal commercial practice. The filled cans shall be closed in a manner that will insure that the contents will not spill or leak from the container during shipment, handling, storage and redistribution.

Applies to item(s) : 2.

T4.5

Gallons and Quarts: The product shall be packaged as specified in rectangular compound lined, double seamed end metal cans with screw cap closure of the type normally used for this product. All containers shall be such that there will be no interaction chemically or physically with the contents so as to damage the container or alter the strength, quality or purity of the contents. The filled cans shall be provided with inner friction metal seals which shall be rolled or tapped firmly into the screw neck and shall not damage the inner pad or facing. The screw caps shall be designed and secured to insure that the contents will not spill or leak from the containers during shipment, handling, storage and redistribution. One quart containers do not require handles. Gallon size cans shall be provided with a formed bridge type handle or a wire handle secured to the top in accordance with normal commercial practice. When formed bridge type handles are used, padding shall be used to protect the handle.

Applies to item(s) : 5.

PACKING

T5.1

Kits smaller than 2 gallons packaged and assembled as specified above shall be packed in a close-fitting corrugated fiberboard box conforming to Section 6(c), Rule 41 of the Uniform Freight Classification and Item 22 of the National Motor Freight Classification. Closure of the boxes shall be in accordance with Section 7 of Rule 41 of the Uniform Freight Classification. The filled boxes shall not weigh more than 65 pounds. Pails and drums shall meet the applicable requirements of the National Motor Freight Classification, Uniform Freight Classification, and Department of Transportation (49 CFR) regulations. For oversea shipments by vessel, the commodity shall be packaged, packed, and marked in a manner to meet the applicable requirements of International Maritime Organization (IMO), International Maritime Dangerous Goods (IMDG) Code, latest revision.

PRODUCT CONFORMANCE: The products provided shall meet the salient characteristics of this description, conform to the producer's own specifications, standards, and quality assurance practices and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance.

PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed in accordance with the latest revision of ASTM D 3951, Standard Practice for Commercial Packaging. Copies of ASTM standards are available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. Phone: 610-832-9585, Fax: 610-832-9555, Web site: www.astm.org, e-mail: service@astm.org.

South Coast Air Quality Management District Provision: If the item is on an existing contract, the supplier shall follow the pre-arranged California South Coast Air Quality Management District labeling requirements.

Applies to item(s) : 3, 8, 9, 10, 11, 12, 13, 14, 15 and 16.

T5.2

PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed in accordance with the latest revision of ASTM D 3951, Standard Practice for Commercial Packaging. Copies of ASTM standards are available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. Phone: 610-832-9585, Fax: 610-832-9555, Web site: www.astm.org, e-mail: service@astm.org.

GALLONS AND QUARTS: Not more than four one-gallon-size units or 12 one-quart-size units packaged as specified above shall be further packaged in a close fitting corrugated fiberboard box conforming to Section 6(a), Rule 41 of the Uniform Freight Classification and Item 222 of the National Motor Freight Classification. Closure of the boxes shall be in accordance with Section 7 of Rule 41 of the Uniform Freight Classification. The units shall be protected within the box by individually packaging in paperboard boxes or with full height partitions or other suitable means to ensure that the containers are not damaged during shipment, handling, storage, and redistribution.

South Coast Air Quality Management District Provision: If the item is on an existing contract, the supplier shall follow the pre-arranged California South Coast Air Quality Management District labeling requirements.

Applies to item(s) : 4 and 7.

T5.3

Up to twelve cans of material packaged as specified above shall be packed in a close-fitting corrugated fiberboard box conforming to Section 6(a), Rule 41 of the Uniform Freight Classification and Item 222 of the National Motor Freight Classification. Closure of the boxes shall be in accordance with Section 7 of Rule 41 of the Uniform Freight Classification.

South Coast Air Quality Management District Provision: If the item is on an existing contract, the supplier shall follow the pre-arranged California South Coast Air Quality Management District labeling requirements.

Applies to item(s) : 2.

T5.4

Rectangular gallons and quarts of material packaged as specified above shall be packed in a close-fitting corrugated fiberboard box conforming to Section 6(a), Rule 41 of the Uniform Freight Classification and Item 222 of the National Motor Freight Classification. Closure of the boxes shall be in accordance with Section 7 of Rule 41 of the Uniform Freight Classification. Gallons shall be packed 6 to a box and quarts shall be packed 24 to a box. Full length and width fiberboard pads shall be used to separate tiers.

Applies to item(s) : 5.

MARKING

T6.1

All unit, intermediate, transport packages and unit loads shall be marked and bar coded for delivery to civilian activities in accordance with the latest version of FED-STD-123, "Marking For Shipment (Civil Agencies)", or marked and bar coded for delivery to military activities in accordance with the latest version of MIL-STD-129, "Military Marking For Shipment and Storage". "Latest version" is defined as the version in effect on the date of bid submittal. Federal Standards and Military Standards can be accessed on-line via the Defense Logistics Agency's "Assist" Quicksearch web site:

http://assist.daps.dla.mil/quicksearch/.

South Coast Air Quality Management District Provision: If the item is on an existing contract, the supplier shall follow the pre-arranged California South Coast Air Quality Management District labeling requirements.

Palletization: The shipping (transport) containers shall be palletized. The pallets shall be 48-inch length x 40-inch width, general purpose, four-way entry, flush stringer, and double-face non-reversible pallets. The palletized load shall not exceed 2500 pounds in weight for shipments to the Eastern Distribution Center (Burlington). The palletized load shall not exceed 2000 pounds in weight for shipments to the Western Distribution Center (French Camp Location). The palletized load shall not overhang the pallet deck board edge by more than 1 inch and shall not exceed 53 inches in overall height (including pallet). Less than half pallet loads or loads shipped by small package carrier in acceptable transport packing need not be palletized. When less than full but more than a half pallet is used, the palletized load shall utilize proper bracing and/or reinforcement to ensure that the load can withstand two additional loads placed on it.

Stacking: A load-stacking test shall be performed once, at the beginning of the contract, for each different unitized or palletized load configuration. A fully palletized load shall be tested utilizing a total stack of three palletized loads, with all the proper bracing and/or reinforcement necessary to perform the test. There shall be no evidence of damage to the pallets, shipping containers or products when stack is tested on the rigid surface for a minimum of 24 hours, in compliance with all the National and Local Safety Regulations. The pre-tested palletized load configuration shall be duplicated using the same packaging materials, pattern, number of shipping (transport) containers, and procedures consistent throughout the duration of the contract. Palletized loads shall be stable and safe when handled with mechanical equipment by qualified personnel.

Materials: All lumber used inside or outside a shipment shall be bark free. No used wood pallets with repaired components or stringers will be acceptable. All wood pallet stringers shall be manufactured from hardwoods. Pallets manufactured of materials other than wood, shall conform to all the requirements specified herein.

Unitization: For the purpose of this requirement, the assembled group of containers or items in a single load that can be handled as a unit throughout the distribution system. Unitization encompasses, but is not limited to, consolidation in a container, placement on a pallet or load base having forklift capability, or securely binding together. Shipments should be considered for unitization where appropriate or specified.

Unitization of pallet load: The palletized load shall be unitized and secured to the pallet to insure that the load arrives intact without product damage. The containers or items shall be placed in a suitable pattern to form a stable and balanced load. Vertical, horizontal or filler reinforcement shall be added as necessary to meet the stacking strength requirements. A palletized load shall be secured to the pallet by shrink or stretch wrapping, and/or, by steel or nonmetallic strapping. When steel or nonmetallic strapping is used, edge protectors shall be provided to prevent damage to the cartons when tensioning the strapping. As a minimum, two straps shall run lengthwise, two straps shall run widthwise, and two straps shall run around the girth of the palletized load. A palletized load shall be capable of protecting the products against damage in a multiple handling, transportation, and storage environment having distribution warehouses with rack systems that support the load/s overhead of warehouse personnel.

Notice of special requirements for shipment to European Union countries: Per Clause D-FSS-468, non-manufactured wood pallets and other non-manufactured wood package material used in shipments destined for ultimate delivery to or through a European Union (EU) country shall comply with the Emergency Measures (2001/219/EC) adopted by the Commission of the European Communities (CEC). Additionally, shipments delivered to DoD distribution facilities or freight consolidation points for eventual delivery to or through EU countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17.

Applies to item(s) : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 and 16.

ENVIRONMENTAL FIELDS

TE.1. Shipbuilding NESHAPs compliant

Volatile Organic Hazardous Air Pollutants (VOHAP) Identification for National Emissions Standards for Hazardous Air Pollutants (NESHAP) Shipbuilding Volatile Organic Compound (VOC) Certificates (September 2006).

For each batch of coating product from which any quantity of the coating product is supplied to the Government under this contract, the Contractor agrees to provide the Government with a volatile organic compound (VOC) certification, as described at 40 CFR 63.785 (a)(2). The term "batch" shall have the meaning described at 40 CFR 63.782. The Contractor shall determine the VOC content of each batch in conformance with procedures described at 40 CFR 63.786, or as otherwise approved in writing by the U.S. Environmental Protection Agency. A sample certificate is available for download at the following web site.

http://www.gsa.gov [Select Products & Services] [Select Energy & Environmental] [Select Environmental Products] [Select Safer Paints, Cleaning & Chemical Prod] [Select Pollution Prevention Product Library] scroll down, [select NESHAP Compliance Certificate ]

Note: This will open the 3-page certificate in Adobe Pdf format. You can then save it or print it.

The Government reserves the right to reject as defective any coating product for which the VOC certification has not been timely provided in the manner as outlined below.

Paper copies of the VOC certifications are to be provided with each product shipment. The certificate document is separate from the Material Safety Data Sheet (MSDS) but will be included with all product shipments accompanying the MSDS. For items shipped to consignees identified by mailing address as agency depots, distribution centers or customer supply centers, the Contractor shall provide one copy of the NESHAP Shipbuilding Batch VOC Certificate in or on each shipping container. If affixed to the outside of each container, the NESHAP Batch Certificate must be placed in a weather resistant envelope.

Applies to item(s): 8, 9, 10, 11, 12, 13, 14, 15 and 16

TE.6. PRIME

Packaging for this product is compliant with the U.S. Navy "Plastics Removal in the Marine Environment (PRIME)" program which calls for…