36C25019B0018-009.pdf

PDF 5 MB Posted Apr 12, 2019

Attached to: 1B229 Mechanical Room (VA-19-00027342) Federal contract opportunity
Solicitation number: 36C25019B0018
Issued by: Department of Veterans Affairs Veterans Health Administration Veterans Integrated Service Network 10

About this file

From the source

36C25019B0018 S02 - Combined Drawings - PDFs.pdf

View the file

Other files for this federal contract opportunity

Other files attached to 1B229 Mechanical Room (VA-19-00027342), newest first.
File	Type	Posted
36C25019B0018-011.docx	DOCX document	Apr 12, 2019
36C25019B0018-008.pdf	PDF	Apr 12, 2019
36C25019B0018-010.pdf	PDF	Apr 12, 2019
36C25019B0018-007.docx	DOCX document	Apr 12, 2019
36C25019B0018-012.docx	DOCX document	Apr 12, 2019
36C25019B0018-000.docx	DOCX document	Feb 15, 2019

On GovTribe

Work with this file on GovTribe

Download the original file
Contacts named in this file
Similar government files
Ask GovTribe AI about this file

Try for free Login

Text version

The file's text, extracted by GovTribe without its formatting.

MEDIUM PRESSURE STEAM CONDENSATE

HEATING HOT WATER SUPPLY

HEATING HOT WATER RETURN

MPR

MPS

CHWS

HHWS

HHWR

CHWR CHILLED WATER RETURN

CHILLED WATER SUPPLY

MEDIUM PRESSURE STEAM

PRESSURE GAUGE

FLEXIBLE METAL EXPANSION LOOP ASSEMBLY

HPR HIGH PRESSURE STEAM CONDENSATE

F FIRE SUPPRESSION PIPE

STRAINER

PIPE EXPANSION ANCHOR

PIPE GUIDE

FLEXIBLE PIPE CONNECTOR

THERMOMETER IN PIPE WELL

BALANCING VALVE

E.L.

HEIGHT OF BOTTOM OF PIPE ABOVE FLOOR9'-2"

HVAC PIPING:

SHUTOFF VALVE

REDUCER OR INCREASER

UNION

(SHUTOFF, BALANCE, CHECK)

TRIPLE DUTY VALVE

CHECK VALVE

3-WAY CONTROL VALVE

GAUGE PORT (PETE'S PLUG)

DRAIN VALVE WITH HOSE FITTING

HIGH PRESSURE STEAMHPS

2-WAY CONTROL VALVE

A. CONTRACTOR SHALL FIELD VERIFY CONDITIONS SHOWN ON DESIGN DOCUMENTS PRIOR TO

COMMENCEMENT OF CONSTRUCTION. NOTIFY ENGINEER OF ANY CONDITIONS WHICH WILL NOT PERMIT

THE WORK TO BE PERFORMED AS INDICATED ON THESE DRAWINGS.

B. COORDINATE ALL SHUT-DOWNS OF EXISTING MECHANICAL SYSTEMS WITH OWNER A MINIMUM OF TEN

WORKING DAYS IN ADVANCE.

C. PROVIDE SERVICE CLEARANCE FOR ALL MECHANICAL EQUIPMENT. REFER TO INSTRUCTIONS FROM THE

EQUIPMENT MANUFACTURER.

D. NEW PIPING SHALL NOT BE ROUTED ABOVE ELECTRICAL PANELS. REFER TO ELECTRICAL DRAWINGS

FOR LOCATION OF PANELS.

E. NO TEMPERATURE SENSING CONTROL DEVICES SHALL BE LOCATED OVER HEAT PRODUCING DEVICES.

F. MECHANICAL DRAWINGS ARE DIAGRAMMATIC. WHERE DUCT SIZE SHOWN IS IN CONFLICT WITH

STRUCTURE OR OTHER BUILDING SYSTEM, CONTRACTOR MAY MODIFY DUCT SIZE AND PROVIDE

EQUIVALENT FREE AREA DUCT.

G. WHERE EQUIPMENT IS TO BE REMOVED, REMOVE ALL ASSOCIATED PIPING, DUCTWORK, CONTROLS, CONCRETE PADS, SUPPORTS, ETC. PATCH WALL AND FLOOR OPENINGS TO MATCH ADJACENT

SURFACES.

H. CONTRACTOR SHALL REMOVE AND REPLACE CEILING TILES AND GRID AS REQUIRED TO COMPLETE

DEMOLITION AND NEW WORK IN AREAS OF WORK. CONTRACTOR SHALL BE RESPONSIBLE FOR

REPLACING ANY TILES OR GRID DAMAGED DUE TO THIS WORK.

L. ALL VARIABLE SPEED MOTORS SHALL BE PROVIDED SHAFT GROUNDING RINGS.

M. ALL VAV CONTROLLERS SHALL BE MOUNTED TO ALLOW FULL ACCESSIBILITY.

N. ALL VALVES SHALL BE INSTALLED IN ACCESSIBLE LOCATIONS.

NORMALLY OPENNO

NORMALLY CLOSEDNC

LOCAL DRAIN, VALVED WITH 3/4" THREADED

CONNECTOR

MANUAL AIR VENTMAV

PRESSURE RELIEF VALVE

CD CONDENSATE PIPING

HVAC GENERAL NOTES:

PRESSURE REDUCING VALVE

CALL OUTS:

ROUND DUCT SIZE12"Ø

RECTANGULAR DUCT SIZE24x18

REFERENCE TO CODED NOTE#

SUPPLY AIR DUCT

DUCTWORK SYMBOLS:

RETURN AIR DUCT

EXHAUST AIR DUCT

EXISTING TO REMAIN

EXISTING TO BE REMOVED

EQUIPMENT OR FIXTURE MARK

UNIT NUMBER

EQUIPMENT

TYPE

AFF

AHU

Db dB Dp

AIR CONDITIONING UNIT

ACCESS DOOR

ABOVE FINISHED FLOOR

AIR HANDLING UNIT

ACCESS PANEL

CENTRIFUGAL FAN

COOLING COIL CONDENSATE

CLEAN OUT

COLD WATER

DRY BULB TEMPERATURE

DECIBELS

DEW POINT TEMPERATURE

DIRECT EXPANSION

EX.

FLR.

FSD

EXHAUST AIR

EXHAUST FAN

EXISTING

FORWARD CURVED FAN

FLOOR

FIRE DAMPER

COMBINATION FIRE/SMOKE DAMPER

HEATING COIL

HORSEPOWER

MAX.

MIN.

NOM.

REA

Sp. Gr.

SPS

MAXIMUM

MINIMUM

NOMINAL

OUTDOOR AIR

PRESSURE DROP

PRE-FILTER

PREHEAT

RELIEF AIR

RETURN FAN

REHEAT COIL

RELATIVE HUMIDITY

SUPPLY AIR

SPECIFIC GRAVITY

STATIC PRESSURE

STATIC PRESSURE SENSOR

VSMC

VOLUME DAMPER

VARIABLE SPEED MOTOR CONTROLLER

WET BULB TEMPERATURE

ABBREVIATIONS:

MECHANICAL SYMBOLS:

LIMIT OF DEMOLITION

AND EXISTING WORK

POINT OF CONNECTION BETWEEN NEW

GENERAL SYMBOLS:

EXISTING TO BE RELOCATED

SS STAINLESS STEEL

N.T.S. NOT TO SCALE

TCP TEMPERATURE CONTROL PANEL

SIDE CONNECTION

BOTTOM CONNECTION, 45° OR 90°

TOP CONNECTION, 45° OR 90°

RA RETURN AIR

FLOAT & THERMOSTATIC STEAM TRAP SET

INCLUDING PIPING ACCESSORIES

INVERTED BUCKET STEAM TRAP SET INCLUDING

PIPING ACCESSORIES

ECCENTRIC REDUCER

DIRECTION OF FLOW

D DRAIN

V VENT LINE

SHUTOFF VALVE IN VERTICAL PIPE

PROCESS CHILLED WATER SUPPLY

PROCESS CHILLED WATER RETURN

PCWS

PCWR

GV GRAVITY VENTILATOR

LOW PRESSURE STEAM CONDENSATELPR

LPS LOW PRESSURE STEAM

CFM

CUH

CUBIC FEET PER MINUTE

CABINET UNIT HEATER

DDC DIRECT DIGITAL CONTROL

GPM GALLONS PER MINUTE

PIPE TRANSITION

HZ ZONE HUMIDIFIER

RTU ROOFTOP UNIT

XRL

EXISTING

EXISTING TO BE REMOVED

EXISTING TO BE RELOCATED

GHR

HOT GLYCOL WATER HEATING SUPPLY

HOT GLYCOL WATER HEATING RETURN

GRR GLYCOL WATER RUN-AROUND RETURN

GR GLYCOL WATER RUN-AROUND SUPPLY

VAV- #

CONVERTOR

NO.

HX-1

LOCATION

MECH RM

AB402

FLUID

WATER

GPM

TEMP. IN

°F

TEMP.

OUT

°F

MAX. LOSS

PSI

FLUID

1.0

CIRCULATING FLUID STEAM PSIG

ENT.

CONTROL

VALVE

ENT.

CONVERTOR

10 5

CONTROL

VALVE

LBS/HR

TRAP

LBS/HR

HX-2

STEAM-TO-HOT WATER CONVERTOR SCHEDULE

MARK

SERVICE

TYPE

EXPANSION TANK

CAPACITY

TANK VOLUME (GAL.)

PHYSICAL SIZE

ET-1

HOT WATER

VERT. BLADDER

20"Ø X 41"T

NOTES:

1. MOUNT ON 4" THICK CONCRETE HOUSEKEEPING PAD.

2. REFER TO SPECIFICATIONS FOR ADDITIONAL INFORMATION.

MARK

SERVICE

AIR SEPARATOR

CAPACITY

INLET/OUTLET SIZE

ASME RATED

AS-1

HOT WATER

YES

NOTES:

1. REFER TO SPECIFICATIONS FOR ADDITIONAL INFORMATION.

WATER FLOW (GPM)

MARK

SERVICE

TYPE

TEMPERATURE (°F)

PUMPS

MEDIA

PERFORMANCE

FLOW (GPM)

TOTAL HEAD (FEET)

SPEED (RPM)

MOTOR

SIZE (HP)

VOLT-PHASE-HERTZ

HWP-1, 2

HOT WATER

100% WATER

3.0

460-3-60

EFFICIENCY (%) 57.0

NOTES:

1. INSTALL WITH MANUFACTURER'S REQUIRED NET POSITIVE SUCTION HEAD

(NPSH).

2. MOUNT PUMP ON CONCRETE INERTIA PAD.

3. PUMP CAPACITY SHOWN IN SCHEDULE INDICATES TOTAL FUTURE LOAD OF

SYSTEM.

4. AT CONCLUSION OF THIS PROJECT, PUMPS SHALL BE SET TO 60 GPM,

CONSTANT VOLUME.

4. REFER TO SPECIFICATIONS FOR ADDITIONAL INFORMATION.

5. VSMC BY EC.

6. MOTORS SHALL BE PROVIDED WITH SHAFT GROUNDING RINGS.

NOTES 1,2,3,4,5,6

VARIABLE SPEED MOTOR CONTROLLER YES

NOTES:

1. CONVERTORS SHALL BE INSULATED PER MECHANICAL SPECIFICATIONS.

2. CAPACITY SHOWN IN SCHEDULE INDICATES TOTAL FUTURE LOAD OF SYSTEM.

3. 2-PASS, L=60", 8-5/8" DIA., WEIGHT = 425 LBS.

BASE MTD,

END SUCTION

0.5HEAD LOSS (FT)

PRECHARGE (PSI) 12

SYSTEM EXPANSION (GALLONS) 23.1

MAX. DESIGN TEMPERATURE (°F) 180

ACCEPTANCE VOLUME (GALLONS) 37

ET-#HX-#

HWP-#

AS-#

YES

STRAINER

ASME RATED YES

MECH RM

AB402

WATER 84 150 180 1.0 10 5 1281 2562

RECONFIGURE 1B-229

MECHANICAL ROOM

541-18-510CONSULTANTS: ARCHITECT:

o n e e ig h th i n c h o n e f o o t o n e q u a rt e r in c h o n e f o o t th re e e ig h th s i n c h o n e f o o t o n e h a lf i n c h o n e f o o t th re e q u a rt e rs i n c h o n e f o o t o n e i n c h o n e f o o t o n e a n d o n e h a lf i n c h e s o n e f o o t th re e i n c h e s o n e f o o t

VA FORM 08-6231, OCT 1978

1 2 3 4 5 6 7 8 9 10

VAMC - WADE PARK

10/02/18

10/02/2018

FULLY SPRINKLERED

DESIGN AND CONSTRUCTION DOCUMENTS AS

INSTRUMENTS OF SERVICE ARE GIVEN IN

CONFIDENCE AND REMAIN THE PROPERTY OF

PERSPECTUS ARCHITECTURE. THE USE OF THIS

DESIGN AND THESE CONSTRUCTION DOCUMENTS

FOR PURPOSES OTHER THAN THE SPECIFIC

PROJECT NAMED HEREIN IS STRICTLY PROHIBITED

WITHOUT THE EXPRESSED WRITTEN CONSENT OF

PERSPECTUS ARCHITECTURE.

CONSULTANTS:

Final Construction Documents

74490

L.D. HENDRIX, JR

R E

O F

NOIS

N E

ERT

L EA

E I N

A HF OO

MECHANICAL SYMBOLS,

SCHEDULES, AND NOTES

1-M1

LDHLDH

STEEL EXPANSION SHIELD FOR

THIS TYPE SHALL BE USED ONLY

INSERTS FOR NEW CONSTRUCTION

FOR EXISTING CONSTRUCTION AND

3/8" (10 MM) MIN DIA EXPANSION BOLTS

NUTS & WASHERS

HANGER RODS

3/8" (10 MM) MIN DIA

FLOOR SLAB

CLIP

ANGLE

HANGER RODS

3/8" (10 MM) MIN DIA

TURNBUCKLE

IN SLABS OR BEAMS OF

INSERTS FOR NEW CONSTRICTION

EXISTING CONSTRUCTION AND

4" (100 MM) MIN DEPTH

CONCRETE

3/8" (10 MM) MIN DIA

INSERTS NEW

CONSTRUCTION ONLY.

NOTE: FOR TRAPEZE HANGER TAKE SPACING OF SMALLEST SIZE ON TRAPEZE.

MAXIMUM PIPE/TUBING SUPPORT SPACING

TUBING 5 FT

NOM. SIZE

PIPE

THRU (20)

6 8 10

(32)(25) (40)

(65)

(50)

(75)

ADJUSTABLE CLEVIS HANGER

TYPE 43 - SEE SPECIFICATIONS

SADDLE

WELD

1312 14 16

(125)(100)

(150)

(200)

TO 1000 LB. (453 KG) UNIFORM LOAD

TRAPEZE HANGER FOR UP

PROVIDE INSULATION SHIELD

SIDE VIEW

1 5/8" (43 MM) 12 GAGE1" (25 MM) MAX.

STRENGTH INSULATION

PROVIDE HIGH COMPRESSIVE

TYPE 1 - SEE SPECIFICATIONS

ADJUSTABLE CLEVIS HANGER

HANGER ROD

UNDER INSULATION SHIELD

AT HANGER

INSULATION SHIELD

TEMPERATURE PIPE)

REQUIRED FOR LOW

BARRIER TYPE IS

INSULATION (VAPOR

SPACING ON

36" (900 MM) MAX.

BAND

(9 PCF MIN. DENSITY)

HANGER RODS WITH

(8" (200 MM) MIN.)

CHANNEL OR 2"x2"x1/4"

(50x50x8 MM) ANGLE

864 532 2 1/21 1/21 1 1/4IN.

(MM)

(M)

FT.

(M)

(5.8)(5.2)(4.1) (4.9)(3.7)(3.0) (3.4)(2.7)(2.1)

(4.9)(4.1)(3.7) (4.0)(3.0)(2.4)(1.8)5 FT

THRU 3/4

(2.1) (2.1)

(2.1)

(2.7)

(2.4)

1/2" (15 MM) DIA.

EACH CHANNEL

AND INSERT FOR ALL PIPING

NOTE:

1. APPLICABLE TO PENETRATIONS OF ALL

FIRE RATED MEMBRANES, IN

ACCORDANCE WITH NFPA 101. REFER

TO SPECIFICATIONS SECTION FOR FIRE

STOPPING SYSTEMS.

INSULATED PIPE

OR DUCT

FLOOR

FIRESTOP MATERIAL

3/4" [19mm] APPROVED

FIRESTOP INSULATION

WITH VAPOR BARRIER

PIPE SLEEVE

1/4" [6mm]Ø ANCHOR

ROD FOR NEW

CONSTRUCTION

WELD

FLOOR OR DECK PENETRATION

PARTITION OR CHASE PENETRATION

6" [152mm]

MASONRY

PARTITION

PARTITION SUPPORT

FIRESTOP

MATERIAL

[152mm]

6" [152mm]

3/4" [19mm] APPROVED

FIRESTOP INSULATION WITH

VAPOR BARRIER

DRYWALL PARTITION

INSULATED

PIPE OR

DUCT

VENT ALL HIGH POINTS INDICATED ABOVE.

IF AUTOMATIC AIR VENTS ARE USED, PIPE DISCHARGE TO DRAIN

NOTES:

PLANS LOCATE DRAIN AT BOTTOM OF SCALE POCKET.

TYPICAL WATER PIPING

REDUCER, IF REQUIRED

3/4" (20 MM) GATE VALVE

ADAPTER TO 20 MM (3/4") HOSE THREAD.

PROVIDE HOSE CAP NUT

NOTES:

ELEVATION

THREADED PIPING WELDED PIPING

ELEVATION

1/4" (8 MM)

COPPER TUBING

1/2" (15 MM)

GATE VALVE

1/2" (15 MM) x 4" (100 MM)

REDUCER

CIRCULATING WATER PIPING

WHERE SCALE POCKETS ARE SHOWN ON PIPE RISER DIAGRAMS AND/OR

DRAIN ALL LOW POINTS AS INDICATED ABOVE.

NIPPLE

ELEVATION

NOTES:

CONNECT TO SIDE OF MAIN TO PREVENT AIR OR DEBRIS FROM ENTERING PIPE TO TANK, TOP OR BOTTOM

CONNECTION NOT PERMITTED.

PROVIDE 12" MINIMUM DROP ANTI-THERMOSYPHON LOOP TO PREVENT GRAVITY HEATING OF TANK.

MOUNT EXPANSION TANK ON 4" CONCRETE HOUSEKEEPING PAD.

FOR HEATING HOT WATER SYSTEM, FILL LINE SHALL BE PIPED FROM DOMESTIC COLD WATER.

HANGER ROD

SUPPORTS

HIGH

CAPACITY

FLOAT TYPE

AIR VENT

FILL LINE. REFER TO

FILL LINE DETAIL. SEE

NOTE 4.

AIR SEPARATOR. SEE

SCHEDULE

VERTICAL

EXPANSION TANK

SEE NOTE 1 AIR VENT

1-1/2"

GLOBE VALVE

PIPE TO LPR MAIN

F&T TRAP ASSEMBLY

REFER TO DETAIL

UNION (TYP)

DIRT LEG. FULL SIZE OF

HEAT EXCHANGER RETURN

OPENING.

BYPASS LINE

PIPE TO LOCAL FLOOR DRAIN

PROVIDE STEEL SADDLE SUPPORTS AND LEGS

SUPPORTED FROM FLOOR FOR EACH HEAT

EXCHANGER. SUPPORT HEIGHT SHALL ALLOW

FOR GRAVITY FLOW OF CONDENSATE TO

CONDENSATE PUMP

THREADED CAP

3/4" DRAIN VALVE

TEST PLUG (TYP)

FLANGE

NOTE: ARRANGE PIPING

TO ALLOW FOR TUBE

REMOVAL

ASME PRESSURE

RELIEF VALVE

PRESSURE

GAUGE (TYP)

THERMOMETER

(TYP)

STEAM CONTROL

VALVES SIZED AT 1/3

AND 2/3 CAPACITY

THERMOSTATIC

AIR VENT

GLOBE VALVE

3/4" BYPASS LINE

STRAINER (TYP)

GLOBE VALVE

BYPASS LINE, SIZE

SAME AS 2/3

CONTROL VALVE

SHUT OFF VALVE

(TYP)

DIRT LEG

PIPE TO

LPR MAIN

2'-0" MIN.

NOTES:

1. INSTALL ALL THERMOMETERS, PRESSURE GAUGES, AND MEASURING DEVICES AT

ELEVATION AND DIRECTION WITH CLEAR VIEW.

FLANGE

DRAIN VALVE

2-POSITION

SOLENOID VALVE,

FULL LINE SIZE.

FROM SYSTEM

TO SYSTEM

3/4"

FLANGE (TYP)

CONCRETE

(TYPICAL)

VIBRATION ISOLATOR

1" (25 MM) MIN. DIA.

DRAIN

1/2" (15 MM)

FLEXIBLE CONNECTOR (TYPICAL)

HANGER

RIGID PIPE

HANGER

RIGID PIPE

PIPE & SMALLER. TYPE "H-P" FOR 5"

TYPE. TYPE "H" FOR 4" (100 MM) DIA.

BRANCH SHALL BE SPRING & NEOPRENE

FIRST 3 HANGERS FOR EACH PIPE AND

TO PIPE ELBOW AS POSSIBLE (TYPICAL)

INSTALL HANGER AS CLOSE

FLOOR

PUMP WITH BUILT-IN

SUCTION DIFFUSER

PRESSURE GAGE

(125 MM) DIA. PIPE & LARGER.

STRAINER

PIPE STAND

INERTIA BASE

BALANCE VALVE

NOTES:

1. UNLESS SPECIFICALLY NOTED, SHUT-OFF VALVES INDICATED SHALL BE

GATE, BUTTERFLY, OR BALL VALVES. REFER TO MECHANICAL

SPECIFICATIONS FOR ADDITIONAL REQUIREMENTS.

CHECK VALVE

ISOLATION VALVE, TYP.

BY HCBY PC

DOMESTIC

COLD WATER.

ISOLATION VALVE. TYPICAL.

UNION. TYPICAL.

PRESSURE REDUCING VALVE.

REDUCED

PRESSURE

BACKFLOW

PREVENTER.

MAKE UP WATER

TO EQUIPMENT

BY HC.

PRESSURE GAUGE.

BYPASS.

EXTEND DRAIN LINE TO

NEAREST FLOOR DRAIN.

TERMINATE WITH AN AIR GAP.

NOTE:

A. SET PRESSURE REDUCING VALVE TO SYSTEM STATIC PRESSURE + 4 PSIG FOR FILL

LINE TO HEATING HOT WATER SYSTEM.

F&T TRAP

GLOBE VALVE BYPASS

(NORMALLY CLOSED)

STRAINER

UNION (TYP.)

SHUTOFF VALVE (TYP.)

LPR

L P

12"

MIN.

DIRT LEG FULL

MAIN SIZE

NOT TO SCALE 10

HANGER RODS IN CONCRETE SLABS

AND BEAMS DETAILS

NOT TO SCALE 2

PIPING DRAIN VALVE CONNECTIONS DETAIL

NOT TO SCALE 6

AIR CONTROL, EXPANSION TANK, AND PIPING

CONNECTIONS FOR HYDRONIC SYSTEMS

NOT TO SCALE 1

AIR VENT DETAIL

NOT TO SCALE 4

PIPE/DUCT PENETRATION OF

FIRE/SMOKE DETAILS

NOT TO SCALE 7

TYPICAL PIPE HANGERS DETAILS

NOT TO SCALE 8

FILL LINE DETAIL

NOT TO SCALE 9

FLOAT AND THERMOSTATIC STEAM

TRAP ASSEMBLY DETAIL

NOT TO SCALE 5

END SUCTION BASE MOUNTED PUMP DETAIL

NOT TO SCALE 3

TYPICAL STEAM TO HOT WATER CONVERTOR DETAIL

RECONFIGURE 1B-229

MECHANICAL ROOM

541-18-510CONSULTANTS: ARCHITECT:

VA FORM 08-6231, OCT 1978

1 2 3 4 5 6 7 8 9 10

VAMC - WADE PARK

10/02/18

10/02/2018

FULLY SPRINKLERED

DESIGN AND CONSTRUCTION DOCUMENTS AS

INSTRUMENTS OF SERVICE ARE GIVEN IN

CONFIDENCE AND REMAIN THE PROPERTY OF

PERSPECTUS ARCHITECTURE. THE USE OF THIS

DESIGN AND THESE CONSTRUCTION DOCUMENTS

FOR PURPOSES OTHER THAN THE SPECIFIC

PROJECT NAMED HEREIN IS STRICTLY PROHIBITED

WITHOUT THE EXPRESSED WRITTEN CONSENT OF

PERSPECTUS ARCHITECTURE.

CONSULTANTS:

Final Construction Documents

74490

L.D. HENDRIX, JR

R E

O F

NOIS

N E

ERT

L EA

E I N

A HF OO

MECHANICAL DETAILS

1-M2A

SUB-BASEMENT (FULL HEIGHT)

BASEMENT

R E

A W

A Y

ROOF

GLOBE

PILOT

VENT TO EXTERIOR.

1300#/HR

430#/HR

870#/HR

HIGH PRESSURE

TRAP

ECCENTRIC

INCREASER/

DECREASER, TYP.

4 PIPE DIAMETERS

EXISTING CONDENSATE PUMP

1-1/2"

2-1/2"

3"3"

3/4"3/4"

V E

N T

LPS

LPR

S E

P A

R A

T O

AUTOMATIC AIR VENT, TYP.

REFER TO DETAIL PIPING

ARRANGEMENT AND

SPECIALTIES AT AIR

SEPARATOR AND EXPANSION

TANK.

REFER TO PUMP DETAIL FOR

DETAILED PIPING ARRANGEMENT AND

SPECIALTIES.

1-1/2"

DOMESTIC

COLD WATER.3/4" FILL LINE TO

EQUIPMENT BY MC.

FILL LINE WATER PRESSURE

REDUCING STATION - REFER TO

DETAIL.

3" 3"

E X

P A

N S

T A

N K

HHWS

HHWR

HEATING WATER

HEAT EXCHANGER

HEATING WATER

HEAT EXCHANGER

1,281

LBS/HR

1,281

LBS/HR

REFER TO HEAT EXCHANGER DETAIL

FOR DETAILED PIPING ARRANGEMENT

AND SPECIALTIES.

2/3

1/3

2/3

1/3

1-1/4"

1-1/2"

MECH ROOM

AB402

3/4" VALVES FOR

POT FEEDER CONNECTION

HPS

HPR

SUB-BASEMENT (CRAWLSPACE)

BASEMENT

SCALE: NONE

STEAM AND HEATING HOT

WATER PIPING SCHEMATIC

2-1/2" 3/4"

RECONFIGURE 1B-229

MECHANICAL ROOM

541-18-510CONSULTANTS: ARCHITECT:

VA FORM 08-6231, OCT 1978

1 2 3 4 5 6 7 8 9 10

VAMC - WADE PARK

10/02/18

10/02/2018

FULLY SPRINKLERED

DESIGN AND CONSTRUCTION DOCUMENTS AS

INSTRUMENTS OF SERVICE ARE GIVEN IN

CONFIDENCE AND REMAIN THE PROPERTY OF

PERSPECTUS ARCHITECTURE. THE USE OF THIS

DESIGN AND THESE CONSTRUCTION DOCUMENTS

FOR PURPOSES OTHER THAN THE SPECIFIC

PROJECT NAMED HEREIN IS STRICTLY PROHIBITED

WITHOUT THE EXPRESSED WRITTEN CONSENT OF

PERSPECTUS ARCHITECTURE.

CONSULTANTS:

Final Construction Documents

74490

L.D. HENDRIX, JR

R E

O F

NOIS

N E

ERT

L EA

E I N

A HF OO

STEAM AND HEATING HOT

WATER PIPING SCHEMATIC

1-M2B

GENERAL CONTROLS NOTES:

A. IN DIAGRAMS, 'I' INDICATES AN INPUT, 'O' INDICATES AN OUTPUT.

B. TEMPERATURE CONTROL TEST SHALL INCLUDE, BUT NOT BE LIMITED TO:

• VALVE ACTUATION RESPONSE AND VALIDATION OF CORRECT OPERATION

• VERIFIED ENTIRE CONTROL SEQUENCE OPERATES PER DESIGN

• ACCOUNT FOR ALL CONTROL POINTS LISTED

I - HOT WATER PUMP 2 STATUS

I - HOT WATER SUPPLY TEMP

I - HOT WATER PUMP 1 VFD FAULT

O - HOT WATER PUMP 1 VFD SPEED

I - HOT WATER PUMP 2 VFD FAULT

O - HOT WATER PUMP 2 VFD SPEED

O - HOT WATER PUMP 2 START/STOP

I - HOT WATER PUMP 1 STATUS

O - HOT WATER PUMP 1 START/STOP

VFD

HWP-2

HWP-1

HHWS

I - HOT WATER RETURN TEMP

O - STEAM VALVE 2/3

O - STEAM VALVE 1/3

HHWS

HHWR HHWR

1. STEAM TO HOT WATER CONVERTERS

HEAT EXCHANGER SYSTEM RUN CONDITIONS:

THE HEAT EXCHANGER SYSTEM SHALL BE ENABLED AT ALL TIMES.

HOT WATER PUMP OPERATION:

THE HOT WATER PUMPS SHALL OPERATE IN A LEAD/STANDBY FASHION.

• THE PUMPS SHALL RUN IN CONSTANT VOLUME WATER FLOW. THE CONTROLLER SHALL MAINTAIN

CONSTANT VOLUME WATER FLOW OF 60 GPM (ADJ.) FOR THE LEAD PUMP.

• ON FAILURE OF THE LEAD PUMP, THE STANDBY PUMP SHALL RUN AND THE LEAD PUMP SHALL

TURN OFF. THE STANDBY PUMP SHALL BECOME THE LEAD PUMP AND SHALL MAINTAIN

CONSTANT VOLUME WATER FLOW OF 60 GPM (ADJ.).

• BUILDING MANAGEMENT SYSTEM SHALL CONTROL LEAD/STANDBY PUMPS TO SHARE RUNTIME

HOURS EQUALLY.

• EACH PUMP IS SIZED FOR FUTURE WATER FLOW OF 84 GPM.

O - STEAM VALVE 1/3

O - STEAM VALVE 2/3

O - HOT WATER ISOLATION VALVE

SEQUENCE OF HEAT EXCHANGER SYSTEM

HEAT EXCHANGER OPERATION:

THE HEAT EXCHANGERS SHALL OPERATE IN A LEAD/STANDBY FASHION.

• THE LEAD HEAT EXCHANGER SHALL RUN FIRST. THE HOT WATER ISOLATION CONTROL

VALVE SHALL OPEN.

• THE HOT WATER ISOLATION CONTROL VALVE SHALL BE INTERLOCKED WITH THE

RESPECTIVE STEAM CONTROL VALVES.

• THE CONTROLLER SHALL MODULATE THE STEAM CONTROL VALVES TO MAINTAIN A FIXED

HOT WATER SUPPLY TEMPERATURE SETPOINT OF 180°F (ADJ.).

• THE STEAM VALVES SHALL BE INTERLOCKED WITH THE HOT WATER FLOW SWITCH.

• THE STANDBY HEAT EXCHANGER'S VALVES SHALL REMAIN CLOSED UNTIL THE HEAT

EXCHANGER IS PLACED INTO THE LEAD OPERATION. BUILDING MANAGEMENT SYSTEM

SHALL CONTROL LEAD/STANDBY HEAT EXCHANGERS TO SHARE RUNTIME HOURS

EQUALLY.

BTU INDICATION:

MONITOR HEATING WATER SUPPLY AND RETURN TEMPERATURES AND SYSTEM FLOWS AND

CALCULATE AND DISPLAY BTUs DELIVERED BY THE SYSTEM. SET UP PROGRAM FOR TRENDING

DELIVERED BTUs FOR ENERGY MONITORING PURPOSES.

ALARMS:

• PUMP FAILURE.

• PUMP RUNNING IN HAND.

• PUMP RUNTIME EXCEEDED: STATUS RUNTIME EXCEEDS A USER DEFINABLE LIMIT.

• VFD FAULT.

• HIGH HOT WATER SUPPLY TEMPERATURE

• LOW HOT WATER SUPPLY TEMPERATURE

I - HOT WATER FLOW SWITCH

I - HOT WATER SUPPLY

TEMP

HX-1

HX-2

10 PSI

RECONFIGURE 1B-229

MECHANICAL ROOM

541-18-510CONSULTANTS: ARCHITECT:

VA FORM 08-6231, OCT 1978

1 2 3 4 5 6 7 8 9 10

VAMC - WADE PARK

10/02/18

10/02/2018

FULLY SPRINKLERED

DESIGN AND CONSTRUCTION DOCUMENTS AS

INSTRUMENTS OF SERVICE ARE GIVEN IN

CONFIDENCE AND REMAIN THE PROPERTY OF

PERSPECTUS ARCHITECTURE. THE USE OF THIS

DESIGN AND THESE CONSTRUCTION DOCUMENTS

FOR PURPOSES OTHER THAN THE SPECIFIC

PROJECT NAMED HEREIN IS STRICTLY PROHIBITED

WITHOUT THE EXPRESSED WRITTEN CONSENT OF

PERSPECTUS ARCHITECTURE.

CONSULTANTS:

Final Construction Documents

74490

L.D. HENDRIX, JR

R E

O F

NOIS

N E

ERT

L EA

E I N

A HF OO

TEMPERATURE CONTROLS

1-M3

AB400A

AB401

AB401AAB401B

AB401C

AB402

AB403

AB404

AB405

XR-40x20 RA

1 /2

X-MPS

XR-MPS

X -L

P R

X -L

P R

X-LPR

X-LPS

X -L

P S

X-PD

X-V

X -C

H W

-C

H W

X -C

H W

X -C

H W

X -H

P S

X -H

P R

X -L

P S

S L

O P

X-EF

XR-AC-23

XR-UH

XR-AC-24

-O

-SA

XR-SA

XR-SA 1

CAP

X R

-C H

W S

X R

-C H

W R

XR-OA

7 TYP.

CODED NOTES:

1 REMOVE EXISTING AC-24 AND ALL ASSOCIATED DUCTWORK, PIPING, CONTROLS, POWER, CONCRETE

PADS, SUPPORTS, ETC. CAP UTILITIES BACK AT ACTIVE MAIN.

REMOVE EXISTING AC-23 AND ALL ASSOCIATED DUCTWORK, PIPING, CONTROLS, POWER, CONCRETE

PADS, SUPPORTS, ETC. CAP UTILITIES BACK AT ACTIVE MAIN.

REMOVE EXISTING OA DUCTWORK UP THROUGH AREA WAY. PATCH WALL AT PENETRATION. PATCH

GRATING AT TOP OF AREA WAY AS NECESSARY.

REMOVE EXISTING UNIT HEATER COMPLETELY. REMOVE PIPING BACK TO ACTIVE MAIN. REMOVE POWER

AND CONTROLS COMPLETELY.

REMOVE EXISTING LIEBERT CHILLER UNIT COMPLETELY. REMOVE PIPING BACK TO ACTIVE MAIN.

REMOVE CONCRETE PAD, POWER, AND CONTROLS COMPLETELY.

REMOVE EXISTING CHILLER (BUDZER) UNIT COMPLETELY. REMOVE PIPING BACK TO ACTIVE MAIN.

REMOVE CONCRETE PAD, POWER, AND CONTROLS COMPLETELY.

REMOVE EXISTING DUCT TO BOTTOM OF SHAFT. CAP DUCT.

A. REMOVE ALL EQUIPMENT AS INDICATED. REMOVE ALL ASSOCIATED PIPING, DUCTWORK, CONTROLS, ETC. BACK TO ACTIVE SOURCE AND CAP/TERMINATE. NOT ALL PIPING, DUCTWORK, ETC. IS SHOWN, HOWEVER, THE CONTRACTOR SHALL REMOVE THESE ASSOCIATED ITEMS COMPLETELY. FIELD

VERIFY EXISTING CONDITIONS.

B. REMOVE ALL CONCRETE PADS BENEATH DEMOLISHED EQUIPMENT COMPLETELY.

C. PATCH WALL AND FLOOR OPENINGS UPON REMOVAL OF EQUIPMENT, PIPING, DUCTWORK,

CONDUITS, ETC. PATCH WITH LIKE MATERIAL. PROVIDE FIRESTOPPING WHERE NECESSARY.

DEMOLITION GENERAL NOTES:

2 3 4 539 42 46 4737A37B

RECONFIGURE 1B-229

MECHANICAL ROOM

541-18-510CONSULTANTS: ARCHITECT:

VA FORM 08-6231, OCT 1978

1 2 3 4 5 6 7 8 9 10

VAMC - WADE PARK

10/02/18

10/02/2018

FULLY SPRINKLERED

DESIGN AND CONSTRUCTION DOCUMENTS AS

INSTRUMENTS OF SERVICE ARE GIVEN IN

CONFIDENCE AND REMAIN THE PROPERTY OF

PERSPECTUS ARCHITECTURE. THE USE OF THIS

DESIGN AND THESE CONSTRUCTION DOCUMENTS

FOR PURPOSES OTHER THAN THE SPECIFIC

PROJECT NAMED HEREIN IS STRICTLY PROHIBITED

WITHOUT THE EXPRESSED WRITTEN CONSENT OF

PERSPECTUS ARCHITECTURE.

CONSULTANTS:

Final Construction Documents

74490

L.D. HENDRIX, JR

R E

O F

NOIS

N E

ERT

L EA

E I N

A HF OO

SUB-BASEMENT MECHANICAL

ROOM DEMOLITION PLAN

1-M4

LDHLDH

SCALE: 1/4" = 1'0"

2' 4' 8' 16'

SUB-BASEMENT MECHANICAL

ROOM DEMOLITION PLAN

STAIR 2

1B228

1B229

X-HPR

X-PD

X-HPS

XR-LPR

XR-LPS

XR-HWR

XR-HWS

CAP

CODED NOTES:

1 EXISTING ELECTRICAL PANEL TO REMAIN.

REMOVE EXISTING WATER FILTER COMPLETELY. REMOVE ALL ASSOCIATED PIPING, SUPPORTS, ETC.

EXISTING TEMPERATURE CONTROL PANEL TO REMAIN.

EXISTING CONDENSATE PUMP TO REMAIN.

EXISTING STEAM PRESSURE REDUCING STATION TO REMAIN.

REMOVE EXISTING DOMESTIC WATER FILL LINE. CAP BACK AT ACTIVE MAIN.

REMOVE EXISTING EXPANSION TANK COMPLETELY. REMOVE ALL ASSOCIATED PIPING, SUPPORTS, ETC.

EXISTING TEMPERATURE CONTROLS AIR COMPRESSOR TO REMAIN.

REMOVE EXISTING AIR SEPARATOR COMPLETELY. REMOVE ALL ASSOCIATED PIPING, SUPPORTS, ETC.

REMOVE EXISTING HOT WATER PUMP COMPLETELY. REMOVE ALL ASSOCIATED PIPING, POWER,

CONTROLS, SUPPORTS, ETC.

REMOVE EXISTING HEAT EXCHANGER COMPLETELY. REMOVE ALL ASSOCIATED PIPING, CONTROLS, SUPPORTS, ETC.

EXISTING SPOT COOLER TO REMAIN.

VERIFY EXISTING CONDITIONS.

B. REMOVE ALL CONCRETE PADS AND SUPPORTS ASSOCIATED WITH DEMOLISHED EQUIPMENT.

C. PATCH WALL AND FLOOR OPENINGS UPON REMOVAL OF EQUIPMENT, PIPING, DUCTWORK,

CONDUITS, ETC. PATCH WITH LIKE MATERIAL. PROVIDE FIRESTOPPING WHERE NECESSARY.

DEMOLITION GENERAL NOTES:

36.5 38

RECONFIGURE 1B-229

MECHANICAL ROOM

541-18-510CONSULTANTS: ARCHITECT:

VA FORM 08-6231, OCT 1978

1 2 3 4 5 6 7 8 9 10

VAMC - WADE PARK

10/02/18

10/02/2018

FULLY SPRINKLERED

DESIGN AND CONSTRUCTION DOCUMENTS AS

INSTRUMENTS OF SERVICE ARE GIVEN IN

CONFIDENCE AND REMAIN THE PROPERTY OF

PERSPECTUS ARCHITECTURE. THE USE OF THIS

DESIGN AND THESE CONSTRUCTION DOCUMENTS

FOR PURPOSES OTHER THAN THE SPECIFIC

PROJECT NAMED HEREIN IS STRICTLY PROHIBITED

WITHOUT THE EXPRESSED WRITTEN CONSENT OF

PERSPECTUS ARCHITECTURE.

CONSULTANTS:

Final Construction Documents

74490

L.D. HENDRIX, JR

R E

O F

NOIS

N E

ERT

L EA

E I N

A HF OO

FIRST FLOOR MECHANICAL

ROOM 1B-229 DEMOLITION PLAN

1-M5

LDHLDH

SCALE: 1/2" = 1'0"

0' 1' 2' 4' 8'

FIRST FLOOR MECHANICAL ROOM 1B-229

DEMOLITION PLAN

AB400A

AB401

AB401AAB401B

AB401C

AB402

AB403

AB404

AB405

X-MPS

X -L

P R

X -L

P R

X-LPR

X-LPS

X -L

P S

X-PD

X-V

X -C

H W

-C

H W

X -C

H W

X -C

H W

X -H

P S

X -H

P R

X -L

P S

S L

O P

X-EF

H P

H H

W S

H H

W R

H H

W S

H H

W R

VENT

L P

LPR

HWP-1

HX-2HX-1

AS-1

ET-1

2-1/2"

3/4"

2-1/2"

3" 1-1/2"

6HWP-2 6

CODED NOTES:

1 NEW PRESSURE REDUCING STATION. REFER TO PIPING SCHEMATIC AND DETAILS.

REFER TO SUB-BASEMENT MECHANICAL PIPING PLAN (DWG 1-M7) FOR CONTINUATION.

ROUTE 4" VENT UP THROUGH AREA WAY. OFFSET AS NECESSARY IN ORDER TO ROUTE TO OUTSIDE.

RACK PIPE TO AREA WAY WALL. CUT AND RE-SUPPORT GRATING AS NECESSARY.

MOUNT EXPANSION TANK ON 4" CONCRETE HOUSEKEEPING PAD.

MOUNT AIR SEPARATOR FROM STRUCTURE ABOVE.

MOUNT PUMP ON NEW CONCRETE INERTIA PAD.

MOUNT HEAT EXCHANGER ABOVE FLOOR WITH STEEL SUPPORT.

A. FIELD VERIFY EXACT ROUTING OF ALL PIPING WITHIN MECHANICAL ROOM. FIELD VERIFY EXACT

LOCATIONS OF ALL NEW EQUIPMENT.

B. SLEEVE ALL CONCRETE WALL PENETRATIONS. PROVIDE FIRESTOPPING IN RATED CONSTRUCTION.

C. REFER TO MECHANICAL DETAILS (DWG 1-M2A) AND STEAM AND HEATING HOT WATER PIPING

SCHEMATIC (DWG 1-M2B) FOR DETAILED PIPING ARRANGEMENT, CONFIGURATION, AND SIZES.

GENERAL NOTES:

1 2 3 4 539 42 46 4737A37B

RECONFIGURE 1B-229

MECHANICAL ROOM

541-18-510CONSULTANTS: ARCHITECT:

VA FORM 08-6231, OCT 1978

1 2 3 4 5 6 7 8 9 10

VAMC - WADE PARK

10/02/18

10/02/2018

FULLY SPRINKLERED

DESIGN AND CONSTRUCTION DOCUMENTS AS

INSTRUMENTS OF SERVICE ARE GIVEN IN

CONFIDENCE AND REMAIN THE PROPERTY OF

PERSPECTUS ARCHITECTURE. THE USE OF THIS

DESIGN AND THESE CONSTRUCTION DOCUMENTS

FOR PURPOSES OTHER THAN THE SPECIFIC

PROJECT NAMED HEREIN IS STRICTLY PROHIBITED

WITHOUT THE EXPRESSED WRITTEN CONSENT OF

PERSPECTUS ARCHITECTURE.

CONSULTANTS:

Final Construction Documents

74490

L.D. HENDRIX, JR

R E

O F

NOIS

N E

ERT

L EA

E I N

A HF OO

SUB-BASEMENT MECHANICAL

ROOM PLAN

1-M6

LDHLDH

N 0'

SCALE: 1/4" = 1'0"

2' 4' 8' 16'

SUB-BASEMENT MECHANICAL

ROOM PLAN

CODED NOTES:

1 3" HHWS/R UP TO BASEMENT. ROUTE PIPING IN BETWEEN CONCRETE JOIST SPACE. FIELD VERIFY

EXISTING CONDITIONS. REFER TO DWG 1-M8 FOR CONTINUATION.

REFER TO DRAWING 1-M6 FOR CONTINUATION.

PROVIDE 3"Ø FLEXIBLE EXPANSION LOOP FOR HHWS AND HHWR PIPE. FLEXIBLE LOOPS SHALL BE RATED

FOR ±4" OF MOVEMENT AND 288 PSI. FLEXIBLE LOOPS SHALL CONSIST OF TWO FLEXIBLE SECTIONS OF

HOSE AND BRAID, TWO 90° ELBOWS, AND ON 180° RETURN ASSEMBLED IN SUCH A WAY THAT THE PIPING DOES NOT CHANGE DIRECTION, BUT MAINTAINS ITS COURSE ALONG A SINGLE AXIS. LOOPS SHALL BE

INSTALLED IN A NEUTRAL, PRE-COMPRESSED OR PRE-EXTENDED CONDITION AS REQUIRED FOR THE

APPLICATION. MATERIAL OF CONSTRUCTION AND END FITTINGS TYPE SHALL BE CONSISTENT WITH PIPE

MATERIAL AND EQUIPMENT/PIPE CONNECTION FITTINGS. SUPPORT PER MANUFACTURER'S

REQUIREMENTS.

A. SUB-BASEMENT CRAWL SPACE IS APPROXIMATELY 4 FEET HIGH WITH LIMITED CLEARANCE AND

LIGHTING. ACCESS TO SUB-BASEMENT CAN BE ACHIEVED THROUGH SUB-BASEMENT PLUMBING

STORAGE, RADIOLOGY SOILED UTILITY FLOOR ACCESS HATCH, STAIR #8, AS WELL AS OTHER STAIR

ACCESS POINTS.

B. THE LARGE QUANTITY OF EXISTING PIPE AND CONDUIT WILL REQUIRE MULTIPLE OFFSETS AND

CHANGES IN ELEVATION AND DIRECTION.

C. SLEEVE ALL PENETRATIONS OF CONCRETE/MASONRY CONSTRUCTION. PROVIDE FIRESTOPPING AT

PENETRATIONS OF RATED CONSTRUCTION.

GENERAL NOTES:

AB200

AB201

AB202

AB203

AB204

AB205AB206

AB401C

X -H

P S

X -P

D X

-H P

R X

-C H

W S

X -C

H W

X -H

P S

X -C

P D

X -H

P R

X -C

H W

X -C

H W

X -P

S L O

P E

X -H

P S

X -H

P R

S L O

P E

1 /2

H P

S H

P R

H H

W S

H H

W R

2-1/2"

H H

W S

H H

W R

H H

W S

H H

W R

H H

W S

H H

W R

3/4"

1 237 39 4237A37B

RECONFIGURE 1B-229

MECHANICAL ROOM

541-18-510CONSULTANTS: ARCHITECT:

VA FORM 08-6231, OCT 1978

1 2 3 4 5 6 7 8 9 10

VAMC - WADE PARK

10/02/18

10/02/2018

FULLY SPRINKLERED

DESIGN AND CONSTRUCTION DOCUMENTS AS

INSTRUMENTS OF SERVICE ARE GIVEN IN

CONFIDENCE AND REMAIN THE PROPERTY OF

PERSPECTUS ARCHITECTURE. THE USE OF THIS

DESIGN AND THESE CONSTRUCTION DOCUMENTS

FOR PURPOSES OTHER THAN THE SPECIFIC

PROJECT NAMED HEREIN IS STRICTLY PROHIBITED

WITHOUT THE EXPRESSED WRITTEN CONSENT OF

PERSPECTUS ARCHITECTURE.

CONSULTANTS:

Final Construction Documents

74490

L.D. HENDRIX, JR

R E

O F

NOIS

N E

ERT

L EA

E I N

A HF OO

SUB-BASEMENT MECHANICAL

PIPING PLAN

1-M7

LDHLDH

SCALE: 1/8" = 1'0"

4' 8' 16' 32'

SUB-BASEMENT MECHANICAL PIPING PLAN

X-HPR

X-PD

X-HPS

HHWS

HHWR

1B228

1B229

X-24x14 EA

6 6 77

8 9

HHWS

HHWR

10BB220

BB219

C15D

C21H1

C15C

BB218

CODED NOTES:

1 3" HHWS/R DOWN TO BASEMENT. REFER TO PARTIAL BASEMENT PLAN (THIS DRAWING) FOR

CONTINUATION. COORDINATE PENETRATIONS WITH EXISTING STRUCTURE.

2" HHWS/R VALVED AND CAPPED FOR FUTURE.

3" HHWS/R UP TO FIRST FLOOR MECHANICAL ROOM 1B-229. REFER TO PARTIAL FIRST FLOOR PLAN (THIS

DRAWING) FOR CONTINUATION.

REWORK EXISTING EXHAUST AIR DUCT ABOVE CEILING. PROVIDE (2) 45-DEG ELBOWS IN LIEU OF 90-DEG

ELBOW IN ORDER TO PERMIT INSTALLATION OF HHWS/R PIPING.

REWORK EXISTING MEDICAL AIR, MEDICAL VACUUM, AND OXYGEN PIPING AT WALL AS REQUIRED IN

ORDER TO PERMIT INSTALLATION OF NEW HHWS/R PIPING.

REMOVE AND REINSTALL CEILING GRID AND TILE AS REQUIRED IN ORDER TO COMPLETE ABOVE CEILING

WORK IN OUTLINED AREA.

REWORK SPRINKLER PIPING AS NECESSARY IN OUTLINED AREA.

CUT AND RE-SUPPORT EXISTING RAISED FLOOR SYSTEM IN ORDER TO INSTALL NEW HHWS/R PIPING

AND ASSOCIATED CHASE. REWORK UNDER FLOOR CABLING AS REQUIRED.

3" HHWS/R DOWN TO SUB-BASEMENT. REFER TO DRAWING 1-M7 FOR CONTINUATION. CONCEAL PIPING

IN NEW CHASE. CHASE SHALL EXTEND FROM FLOOR TO CEILING. PAINT TO MATCH EXISTING ROOM

FINISH. COORDINATE PENETRATION WITH EXISTING STRUCTURE. PENETRATION SHALL BE MADE

BETWEEN CONCRETE JOISTS.

REWORK EXISTING 1" PERIMETER HEAT S/R PIPING AS REQUIRED.

36.5 38 36.5 38 38.5

RECONFIGURE 1B-229

MECHANICAL ROOM

541-18-510CONSULTANTS: ARCHITECT:

VA FORM 08-6231, OCT 1978

1 2 3 4 5 6 7 8 9 10

VAMC - WADE PARK

10/02/18

10/02/2018

FULLY SPRINKLERED

DESIGN AND CONSTRUCTION DOCUMENTS AS

INSTRUMENTS OF SERVICE ARE GIVEN IN

CONFIDENCE AND REMAIN THE PROPERTY OF

PERSPECTUS ARCHITECTURE. THE USE OF THIS

DESIGN AND THESE CONSTRUCTION DOCUMENTS

FOR PURPOSES OTHER THAN THE SPECIFIC

PROJECT NAMED HEREIN IS STRICTLY PROHIBITED

WITHOUT THE EXPRESSED WRITTEN CONSENT OF

PERSPECTUS ARCHITECTURE.

CONSULTANTS:

Final Construction Documents

74490

L.D. HENDRIX, JR

R E

O F

NOIS

N E

ERT

L EA

E I N

A HF OO

SCALE: 1/2" = 1'0"

0' 1' 2' 4' 8'

PARTIAL FIRST FLOOR MECHANICAL PLAN

2 SCALE: 1/2" = 1'0"

0' 1' 2' 4' 8'

PARTIAL BASEMENT MECHANICAL PLAN

PARTIAL BASEMENT AND FIRST

FLOOR MECHANICAL PLANS

1-M8

WIRING DEVICES

WIRING TERMINATIONS

GENERAL NOTES

WIRE SIZE

(MIN. #12AWG)

NO. OF CCTS

IN CONDUIT

PHASE

CONDUCTORS

NEUTRALS

GROUND

POWER DISTRIBUTION EQUIPMENT (FLOOR PLAN VIEW)

MOTOR AND MOTOR CONTROLLERS (FLOOR PLAN VIEW)

BRANCH CIRCUIT WIRING

VSD

GENERAL LEGEND

RECONFIGURE 1B-229

MECHANICAL ROOM

541-18-510CONSULTANTS: ARCHITECT:

VA FORM 08-6231, OCT 1978

1 2 3 4 5 6 7 8 9 10

VAMC - WADE PARK

10/02/18

10/02/2018

FULLY SPRINKLERED

DESIGN AND CONSTRUCTION DOCUMENTS AS

INSTRUMENTS OF SERVICE ARE GIVEN IN

CONFIDENCE AND REMAIN THE PROPERTY OF

PERSPECTUS ARCHITECTURE. THE USE OF THIS

DESIGN AND THESE CONSTRUCTION DOCUMENTS

FOR PURPOSES OTHER THAN THE SPECIFIC

PROJECT NAMED HEREIN IS STRICTLY PROHIBITED

WITHOUT THE EXPRESSED WRITTEN CONSENT OF

PERSPECTUS ARCHITECTURE.

CONSULTANTS:

Final Construction Documents

W.T. GIENGER

I ON EL

63889

F EGE

R O

SI NRE

I E

E R

HOF

ELECTRICAL LEGEND

AND GENERAL NOTES

1-E1

JRDWTG

1B264A

1B226A

1B224A

1B217A

1B215A

1B215C

1B217

1B216

1B215

1B214

1B218

1B2321B233

1B229

1B228

1B227

1B225

1B223 1B222

1B2341B241

1B2311B242

1B2301B243

1B224

1B226

1A210

1B351

35.1 35.5 36 36.5 38 38.5 38.6 40 41 42 43

RECONFIGURE 1B-229

MECHANICAL ROOM

541-18-510CONSULTANTS: ARCHITECT:

VA FORM 08-6231, OCT 1978

1 2 3 4 5 6 7 8 9 10

VAMC - WADE PARK

10/02/18

10/02/2018

FULLY SPRINKLERED

DESIGN AND CONSTRUCTION DOCUMENTS AS

INSTRUMENTS OF SERVICE ARE GIVEN IN

CONFIDENCE AND REMAIN THE PROPERTY OF

PERSPECTUS ARCHITECTURE. THE USE OF THIS

DESIGN AND THESE CONSTRUCTION DOCUMENTS

FOR PURPOSES OTHER THAN THE SPECIFIC

PROJECT NAMED HEREIN IS STRICTLY PROHIBITED

WITHOUT THE EXPRESSED WRITTEN CONSENT OF

PERSPECTUS ARCHITECTURE.

CONSULTANTS:

Final Construction Documents

W.T. GIENGER

I ON EL

63889

F EGE

R O

SI NRE

I E

E R

HOF

SCALE: 1/4" = 1'0"

2' 4' 8' 16'

PARTIAL FIRST FLOOR ELECTRICAL DEMOLITION PLAN

D1. ALL EXISTING LIGHTING FIXTURES, RECEPTACLES, SPECIAL SYSTEMS OUTLETS, CONDUIT, WIRING ETC.

THAT WILL NOT BE REUSED IN THE REMODELED INSTALLATION SHALL BE REMOVED UNLESS OTHERWISE

NOTED. THIS DEMOLITION SHALL INCLUDE ALL ELECTRICAL ITEMS SHOWN ON THIS PLAN THAT ARE NOT

DESIGNATED BY "X", "XN" OR "XRR" AND ALL OTHER ADDITIONAL ITEMS THAT ARE NOT SHOWN BUT THAT

MUST BE REMOVED IN ORDER TO PRODUCE A NEAT, FINISHED, PROPERLY FUNCTIONING ELECTRICAL

INSTALLATION. MAINTAIN CIRCUIT CONTINUITY TO ALL EXISTING REUSED ELECTRICAL SYSTEMS

COMPONENTS - PROVIDE ALL CONDUIT AND WIRING NECESSARY TO ACHIEVE THE SAME. THE

CONTRACTOR SHALL FIELD VERIFY THE NATURE AND EXTENT OF ALL DEMOLITION WORK AND SHALL

INCLUDE COST FOR THE SAME IN THE BID SUBMITTAL.

D2. ALL EXISTING REMOVED ELECTRICAL EQUIPMENT, DEVICES, ETC. THAT ARE NOT RETAINED BY THE

OWNER SHALL BE DISPOSED OF BY THE ELECTRICAL CONTRACTOR.

D3. DASHED WALLS ON PLAN INDICATE EXISTING CONSTRUCTION TO BE REMOVED.

D4. REFER TO ELECTRICAL LEGEND FOR ALL SYMBOL DESIGNATIONS. NOTE SPECIAL ATTENTION TO

SELECTED EXISTING DEVICES, WIREWAYS, ETC. MARKED XB, XRR OR XN, AND REMOVE/BLANK OFF, RELOCATE OR REPLACE THESE COMPONENTS AS REQUIRED.

D5. MAINTAIN CIRCUIT CONTINUITY TO ALL EXISTING ELECTRICAL SYSTEM COMPONENTS IN AREAS NOT

BEING REMODELED UNLESS OTHERWISE NOTED. PROVIDE ALL CONDUIT AND WIRING EXTENSIONS

NECESSARY TO ACHIEVE SAME.

D6. THE ELECTRICAL CONTRACTOR SHALL CLOSELY COORDINATE ALL ELECTRICAL DEMOLITION WORK

WITH THE GENERAL AND MECHANICAL CONTRACTORS, AND SHALL DISCONNECT ALL REQUIRED

CIRCUITS IN A TIMELY MANNER.

D7. CONTACT THE ENGINEER IF A QUESTION SHOULD ARISE CONCERNING THE STATUS OF ANY OUTLET, DEVICE, LIGHTING FIXTURE, ETC.

ELECTRICAL DEMOLITION NOTES

CODED NOTES:

PARTIAL FIRST FLOOR

ELECTRICAL DEMOLITION PLAN

1-E2

JRDWTG

DISCONNECT POWER TO EXISTING HOT WATER PUMPS COMPLETE BACK TO SOURCE, REMOVE

ASSOCIATED CONDUIT, WIRING, CONTROLS, ETC.

X-EF

XR-AC-23

XR-UH

XR-AC-24

XR-CHILLER

XR-LIEBERT

UNIT

ASH2

ASH

ASL

LFS1EQ

XASL2

ASH-J

T-ASL2

T-DPL-FS1

DPL-FS1

AB405

AB403

AB402

AB401C

AB401B

AB401A

AB401

AB400A

1 2 3 4 537 39 42 46 4737A37B

RECONFIGURE 1B-229

MECHANICAL ROOM

541-18-510CONSULTANTS: ARCHITECT:

VA FORM 08-6231, OCT 1978

1 2 3 4 5 6 7 8 9 10

VAMC - WADE PARK

10/02/18

10/02/2018

FULLY SPRINKLERED

DESIGN AND CONSTRUCTION DOCUMENTS AS

INSTRUMENTS OF SERVICE ARE GIVEN IN

CONFIDENCE AND REMAIN THE PROPERTY OF

PERSPECTUS ARCHITECTURE. THE USE OF THIS

DESIGN AND THESE CONSTRUCTION DOCUMENTS

FOR PURPOSES OTHER THAN THE SPECIFIC

PROJECT NAMED HEREIN IS STRICTLY PROHIBITED

WITHOUT THE EXPRESSED WRITTEN CONSENT OF

PERSPECTUS ARCHITECTURE.

CONSULTANTS:

Final Construction Documents

W.T. GIENGER

I ON EL

63889

F EGE

R O

SI NRE

I E

E R

HOF

PARTIAL SUB-BASEMENT

ELECTRICAL DEMOLITION PLAN

1-E3