3595965_ATTACH_EDA.PDF

**Please DOWNLOAD PDF file to local computer and open with Adobe Reader to view contract documents!**

REV: ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

POWER SUPPLY, AC

2. PART NUMBER:

6014810-001

3. NATIONAL STOCK NUMBER:

6130-01-686-1340WF

PREPARED BY:

NEAL BOEHMER

OFFICE SYMBOL:

416 SCMS/GUMAA

DATE:

20210517

HILL AFB FORM 462 Page 1 of 2

4. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC., WILL BE USED IN LIEU OF THE DATA INDICATED. THE

SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO INDICATED.

5. THE SOURCES/MATERIALS IF LISTED ON THE SPECIFICATION, STANDARDS AND DRAWINGS ARE THE ONLY SOURCES/MATERIALS FOR THOSE ITEMS. ANY SUBSTITUTIONS SHALL HAVE PRIOR APPROVAL BY THE COGNIZANT

ENGINEERING ACTIVITY.

6. DEVIATIONS FROM SPECIFICATIONS IDENTIFIED IN CONTROL DRAWINGS ARE NOT AUTHORIZED WITHOUT PRIOR

APPROVAL FROM THE COGNIZANT ENGINEERING.

7. PART MARKING AS PER MIL-STD-130.

8. THIS IS AN AIRCRAFT PART. USE THE APPROPRIATE PORTION OF MIL-STD-2000 THAT APPLIES TO AIRCRAFT SOLDERING FOR ALL SOLDERING REQUIREMENTS. *NOTE: J-STD-001 MAY BE USED IN LIEU OF MILS-STD-2000, IF

SPECIFICATION MEETS OR EXCEEDS MIL-STD-2000

8.1 EFFECTIVE 9 MAY 2005 THE DEPARTMENT OF THE AIR FORCE ISSUED AN AIR WORTHINESS ADVISORY (M-05-01) REGARDING THE USE OF LEAD-FREE SOLDER IN ELECTRICAL AND ELECTRONIC MILITARY PRODUCTS. TO DATE, NO LEAD-FREE SOLDER FORMULATION HAS MATCHED THE RELIABILITY AND PERFORMANCE QUALITIES OF THE STANDARD LEADED SOLDERS. THEREFORE, UNTIL SUCH TIME AS A SUITABLE, RELIABLE LEAD-FREE SOLDER REPLACEMENT IS IDENTIFIED, ALL ELECTRONIC EQUIPMENT SUPPLIERS SHALLCONTINUE TO PROVIDE THE DEPARTMENT OF THE AIR FORCE WITH ITEMS WHICH MEET ALL PERFORMANCE, COMPATIBILITY, AND RELIABILITY STANDARDS PREVIOUSLY ESTABLISHED WITH LEADED SOLDERS. FAILURE TO DO SO, COULD ADVERSELY IMPACT

THE PERFORMANCE AND RELIABILITY OF WEAPON SYSTEMS AFFECTING NATIONAL SECURITY.

8.2 THE USE OF LEAD-FREE SOLDER OR LEAD-FREE PLATED COMPONENTS IN MILITARY ELECTRONIC PRODUCTS IS CONSIDERED A FLIGHT SAFETY AND NATIONAL SECURITY CONCERN. FOR THIS REASON THE US AIR FORCE WANTS TO BE NOTIFIED WHEN LEAD-FREE COMPONENTS AND MANUFACTURING PROCESSES HAVE BEEN IMPLEMENTED. AS PART OF SATISFACTORY COMPLIANCE WITH THE REQUIREMENTS OF THIS CONTRACT THE US AIR FORCE REQUIRES NOTIFICATION ON A NO-COST BASIS WHEN ANY OF THE FOLLOWING CONDITIONS EXIST:1. COMMERCIAL OFF-THE- SHELF (COTS) OR ANY OTHER ELECTRICAL COMPONENTS THAT CONTAIN LEAD-FREE SOLDER OR LEAD-FREE PLATED COMPONENTS ARE USED IN THE END-ITEM. 2. ANY LEAD-FREE COMPONENT OR PART USED TO MANUFACTURE THE END

ITEM THAT IS NOT IDENTIFIED WITH A SEPARATE PART NUMBER OR DESIGNATION.

8.3 IF NO LEAD-FREE, LEAD-FREE PLATED COTS OR ANY OTHER LEAD-FREE ELECTRICAL OR ELECTRONICS COMPONENTS EXIST IN THE MANUFACTURED END ITEM, THE CONTRACTOR SHALL PROVIDE WRITTEN CERTIFICATION OF COMPLIANCE AS A DELIVERABLE WITH THE CONTRACT.1. USE INDUSTRY STANDARD IPC-1066, "MARKING, SYMBOLS AND LABELS FOR IDENTIFICATION OF LEAD-FREE AND OTHER REPORTABLE MATERIALS IN LEAD-FREE ASSEMBLIES, COMPONENTS AND DEVICES," 2. INCLUDE THE PROGRAM ENGINEER'S EVALUATION OF THE PURCHASING/REPAIR ITEM FOR ANY "LEAD-FREE" MILITARY PART(S) IN REFERENCE TO ITS' RELIABILITY, PERFORMANCE AND COMPATIBILITY

FOR THE SYSTEM.

8.4 POC FOR THIS MATTER IS THE ENGINEERING SUPPORT ACTIVITY (ESA).

REV: ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

POWER SUPPLY, AC

2. PART NUMBER:

3. NATIONAL STOCK NUMBER:

6130-01-686-1340WF

PREPARED BY:

NEAL BOEHMER

OFFICE SYMBOL:

416 SCMS/GUMAA

20210517

HILL AFB FORM 462 Page 2 of 2

9 UNIQUE IDENTIFICATION (UID) SHALL BE APPLIED PER MIL-STD-130:

A. MINIMUM 1/8TH INCH ON HUMAN READABLE TO INCLUDE:

1. CAGE (17V)

2. P/N (1P)

3. SERIAL NUMBER (1S)

B. MINIMUM 1/4 INCH SQUARE ON MACHINE READABLE 2D MATRIX – CONSTRUCT 2 – TO

INCLUDE:

1. CAGE (17V)

2. P/N (1P)

3. SERIAL NUMBER (1S)

C. LABEL SHALL CONTAIN ALL DATA ON EXISTING LABEL, IF EXISTING LABEL IS TO BE

REPLACED.

D. SAME LABEL MATERIAL SHALL BE USED AS SPECIFIED IN DRAWING FOR EXISTING

LABEL.

E. MIL-STD-130, ANSI/AIM BCII, ISO 15434, ISO 15415, AND ISO 15418.

ENGINEERING DATA LIST

17 MAY 2021

REVISION: 1 *HISTORY*

CAGE:

12436

PAGE:

NSN:

6130016861340WF

DATA TECH:

Musselman, James N

END ITEM:

F-16

ORGANIZATION/OFFICE SYMBOL:

429 SCMS GUMACA/

MANUFACTURER NAME:

BAE SYSTEMS INFORMATION AND

REFERENCE NUMBER:

NOUN:

POWER SUPPLY

LINE/

SUB CAGE

ENG DRAWING NUM/ ACCOMP

DOC NUM REV

NR

SHEETS

FURN

CODE

DIST

CODE NOUN REMARKS

L 98747 HILL AFB FORM 462 X ENGINEERING DATA

REQUIREMENTS

(ATTACHMENT "A")

STANDARD ENGINEERING TEXT

Musselman, James N 17 MAY 2021

RELEASE OF THIS DATA TO A FOREIGN-OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

NAME: DATE:

C - CLASSIFIED DOCUMENT.

S - FURNISHED WITH SOLICITATION.

M - STABLE BASE DRAWING REQUIRED; FURNISHED WITH

CONTRACT AWARD.

X - DATA SUPPLIED (NOT IN JEDMICS).

R - FURNISHED BY PCO UPON REQUEST.

P - PARTIAL DOCUMENT FURNISHED.

V - VENDOR DRAWING; (NOT PROVIDED).

G - GOV'T DOCUMENT.

O - OTHERS, CONTRACTOR MUST ACQUIRE.

A- DATA NOT AVAILABLE.

FURNISHED METHOD CODE LEGEND:

Page 1 of 1EDL Version 1Generated by PRPS using Jasper Reports on 18 Nov 2022

DD FORM 1423-1, FEB 2001

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

PREVIOUS EDITION MAY BE USED.

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports (0701-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302. Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. Please DO NOT RETURN your form to the above address. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No.

listed in Block E.

A. CONTRACT LINE ITEM NO. B. EXHIBIT C. CATEGORY:

TDP ________ TM _______ OTHER

D. SYSTEM/ITEM E. CONTRACT/PR NO. F. CONTRACTOR

1. DATA ITEM NO. 2. TITLE OF DATA ITEM 3. SUBTITLE

4. AUTHORITY (Data Acquisition Document No.) 5. CONTRACT REFERENCE 6. REQUIRING OFFICE

7. DD 250 REQ

8. APP CODE

9. DIST STATEMENT

REQUIRED

10. FREQUENCY

11. AS OF DATE

12. DATE OF FIRST SUBMISSION

13. DATE OF SUBSEQUENT

SUBMISSION

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

Draft Final

Reg Repro

15. TOTAL

16. REMARKS

17. PRICE GROUP

18. ESTIMATED

TOTAL PRICE

G. PREPARED BY: (Contractor Data Manager) H. DATE I. APPROVED BY: (Engineer) J. DATE

Page of Pages

16. REMARKS (Continued)

16. REMARKS (Continued)

A_CONTRACT_LINE_ITEM_NO:

B_EXHIBIT:

xTDP: Off xTM: Off

OTHER:

DSYSTEMITEM:

E_CONTRACTPR_NO:

FCONTRACTOR:

16_REMARKS_Continued: s. Original drawings are not required. If applicable, reproducible stable base copies of unidimensional drawings and master pattern drawings are required. See Block 14.

Page2: 2 of_pages:

Reset:

xtm: Off

1_DATA_ITEM_NO: A001

2_TITLE_OF_DATA_ITEM: Counterfeit Prevention Plan

3_SUBTITLE: CPP

4_AUTHORITY_Data_Acquisit: DI-MISC-81832

5_CONTRACT_REFERENCE: CLIN for Data

6_REQUIRING_OFFICE: 416 SCMS/GUEAA

7_DID_250_REQ: LT

8_APP_CODE: A

DIST_STATEMENT: D

10_FREQUENCY: ONE/R

11_AS_OF_DATE: SEE BLK 16

12_DATE_OF_FIRST_SUBMISSI: SEE BLK 16

13_DATE_OF_SUBSEQUENT_SUB: SEE BLK 16

addressee1: 416 SCMS/ draft1: 1 reg1: 1 repro1:

addressee2: GUEAA draft2:

reg2:

repro2:

addressee3: 6070 Gum LN draft3:

reg3:

repro3:

addressee4: Bldg. 1213 draft4:

reg4:

repro4:

addressee5: Hill AFB, UT draft5:

reg5:

repro5:

addressee6: 84056-5826 draft6:

reg6:

repro6:

addressee7:

draft7:

reg7:

repro7:

addressee8: SEE BLK 16 draft8:

reg8:

repro8:

addressee9:

draft9:

reg9:

repro9:

addressee10:

draft10:

reg10:

repro10:

addressee11:

draft11:

reg11:

repro11:

addressee12:

draft12:

reg12:

repro12:

addressee13:

draft13:

reg13:

repro13:

addressee14:

draft14:

reg14:

repro14:

addressee15:

draft15:

reg15:

repro15:

addressee16:

draft16:

reg16:

repro16:

addressee17:

draft17:

reg17:

repro17:

addressee18:

draft18:

reg18:

repro18:

addressee19:

draft19:

reg19:

repro19:

addressee20:

draft20:

reg20:

repro20:

addressee21:

draft21:

reg21:

repro21:

addressee22:

draft22:

reg22:

repro22:

addressee23:

draft23:

reg23:

repro23:

addressee24:

draft24:

reg24:

repro24:

addressee25:

draft25:

reg25:

repro25:

addressee26:

draft26:

reg26:

repro26:

addressee27:

draft27:

reg27:

repro27:

addressee28:

draft28:

reg28:

repro28:

addressee29:

draft29:

reg29:

repro29:

addressee30:

draft30:

reg30:

repro30:

addressee31:

draft31:

reg31:

repro31:

addressee32:

draft32:

reg32:

repro32:

addressee33:

draft33:

reg33:

repro33:

addressee34:

draft34:

reg34:

repro34:

addressee35:

draft35:

reg35:

repro35:

addressee36:

draft36:

reg36:

repro36:

addressee37:

draft37:

reg37:

repro37:

addressee38:

draft38:

reg38x:

repro38:

total_draft: 1 total_repro: 0

16_REMARKS: NOTE: Changes to office symbols and/or e-mail addresses when necessary shall be made by letter through the Government CO/ACO without further revision to this CDRL.

1. Block 4: Contractor Format Acceptable.

2. Blocks 7, 8, 14: The contractor shall submit a Letter of Transmittal and send the Contractors Counterfeit Protection Plan (CPP) via e-mail to: adrian.gustai@us.af.mil

3. Blocks 8, 10, 11, 12, 13: The contractor shall deliver the Counterfeit prevention Plan (CPP) NLT thirty (30) calendar days after contract award. The Government comments will be provided to the contractor within fourteen (14) calendar days after receipt. The contractor shall resubmit the CPP NLT seven (7) calendar days after receipt of Government comments.

4. Block 9: Distribution Statement, Export Control Warning and Destruction Notice shall be IAW DoD Instruction 5230.24

The following Distribution Statement shall be placed on the first sheet of each document and/or associated lists.

DISTRIBUTION STATEMENT "D": Distribution authorized to the Department of Defense and U.S. DoD contractors only (Administration or Operational Use). (Nov 2022). Other requests for this document shall be referred to (416 SCMS/GUEAA, Hill AFB, UT 84056-5826).

EXPORT CONTROL WARNING: All printed and electronic, including digital, technical documents that determined to contain export-controlled technical data shall be marked with the following statement:

WARNING: This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et seq.) or the Export Administration Act of 1979 (Title 50, U.S.C., App. 2401 et seq.), as amended. Violations of these export laws are subject to severe criminal penalties. Disseminate IAW provisions of DoD Directive 5230.25.

17_PRICE_GROUP: NSP

ESTIMATED_TOTAL_PRICE: 0.00

G_PREPARED_BY:

H_DATE: 15 Nov 2022

1_APPROVED_BY:

J_DATE: 15 Nov 2022

Page: 1 reg38t: 1

A_CONTRACT_LINE_ITEM_NO:

B_EXHIBIT: A

xTDP: Off

OTHER: MISC

DSYSTEMITEM: Power Supply

E_CONTRACTPR_NO: FD2020-23-00112

FCONTRACTOR:

of_pages: 2

Reset:

xTM: Off

16_REMARKS_Continued: c. DESTRUCTION NOTICE: For classified documents, follow the procedures, in DoD 5220.22-M, National Industrial Security Program Operating Manual (NISPOM), Section 5-705, or DoD 5200.1-R, Information Security Program Chapter VI. For unclassified, limited documents, destroy by any method that will prevent disclosure of contents or reconstruction of the document.

Page2: 2

2022-11-15T09:34:43-0700

PINNEGAR.STEPHANIE.A.1102660737

2022-11-15T10:07:09-0700

GUSTAI.ADRIAN.1245187153

Statement of Work June 2020

PRESERVATION, PACKAGING & MARKING REQUIREMENTS

The contractor shall develop, implement and maintain the preservation, packaging and packing of all items to be delivered under the terms of this contract. Packaging procedures will be established in accordance with AFMCI 24- 201, specifically Paragraph 3.7 and MIL-STD-2073-1, Standard Practice for Military Packaging, Packaging requirements are identified in the AFMC Form 158, Packaging Requirements submitted by the responsible packaging specialist. All “markings and labeling” of shipments shall conform to MIL-STD-129, DoD Standard Practice, Military Marking for Shipment and Storage. The contractor shall affix a completed DD Form 1574, Serviceable Tag-Materiel or DD Form 1574-1, Serviceable Label- Materiel to each unit pack or intermediate container and prime outer container(s). The tag or label will indicate the condition(s) of the materiel and to identify the individual article or contents, bundle, container to which they are securely attached.

INTERNATIONAL STANDARDS FOR PHYTOSANITARY MEASURES

(ISPM 15) REQUIREMENTS

The contractor shall use the wood packaging material regulation for international trade which describes Phytosanitary (including treatments) that have been approved for wood packaging material and provides for the approval of new or revised treatments. Use the latest revision of (ISPM 15), and the following statement complies with the United Nations-implemented restrictions on wood packaging material (WPM).

“This requirement is specifically concerned with invasive species such as pinewood nematode. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frames, and cleats. The statement below cites the requirements in detail and covers lumber for building containers and pallets used for deliveries resulting in worldwide shipments (direct vendor deliveries, Air Logistics complex (ALC), Container Consolidation Points (CCP), Aerial Ports, Water Ports, or other DoD installations).

ELECTROSTATIC MATERIAL (When Applicable)

The Contractor shall apply provisions of MIL-STD-2073-1, when identifying all solid state devices and modules containing diodes, translators, integrated circuits and/or other microelectronic components sensitive to electrostatic forces. All such items shall be packaged IAW MIL- STD-2073- 1 using electrostatic free barrier materials and shall clearly bear “Electrostatic Sensitive Device” labels IAW MIL-STD-129, Department of Defense Standard Practice Military Marking for Shipment and Storage.

PALLETIZED UNIT LOADS

The Contractor shall apply provisions and methods of MIL-STD-147, Palletized Unit Loads to contracts requiring the preparation and shipment of bonded palletized unit loads for DoD facilities when applicable.

SPECIALIZED SHIPPING CONTAINERS

The contractor shall apply provisions of MIL-STD-648, Department of Defense Design Criteria Standard, Specialized Shipping Containers. This standard establishes general design guidelines and associated tests for specialized shipping containers used by the Department of Defense. Definitive requirements for specific containers will be defined by the individual specification, acquisition, or task order. This standard is intended to be used as the basic reference document in all specifications and standards prescribing performance requirements to be applied to a specialized shipping container. Compliance with this intent is expected through normal application of the specification or standard preparation and revision processes.

Statement of Work (Cont)

HAZARDOUS MATERIALS (When Applicable)

The contractor shall ensure Hazardous shipments comply with International Civil Aviation Organization (ICAO), U.S. Code of Federal Regulations (CFR) Title 49, International Air Transport Association (IATA) Dangerous Goods Regulation, International Maritime Dangerous Goods Code (IMDG, Annex 1), and AFMAN 24-204, Preparing Hazardous Materials for Military Air Shipments. Packaging shall meet “DOT specification or a United Nation (UN) specification ” manufactured in accordance with 49 CFR, Part 178 and the final packages assembled IAW 49 CFR, Parts 100-185 as applicable. A Competent Authority Approval (CAA) shall be acquired from the responsible Associate Administrator or other designated Department official to perform a function requiring prior consent under the Hazardous Material Regulation (HMR). Package(s) shall be marked IAW MIL-STD-129, DoD Standard Practice, Military Marking for Shipment and Storage.

The contractor shall affix a completed DD Form 1574, Serviceable Tag-Materiel or DD Form 1574-1, Serviceable Label- Materiel to each unit pack or intermediate container and prime outer container(s). The tag or label will indicate the condition(s) of the materiel and to identify the individual article or contents, bundle, container to which they are securely attached. If a symbol is used to represent the manufacturer or the approval agency certifying compliance with 49 CFR 178, subparts L and M, the symbol must be registered with the U.S. Department of Transportation. A copy of the Contractor’s Test Report and signed certification that the package configuration meets both CFR and UN requirements shall be made available to the procuring contract office, as required, prior to acceptance or shipment of any portion of the product IAW Contract Data Requirements List (CDRL DI-PACK-81059A) (Reference AFMC Form 158). Safety Data Sheets (SDS) are required for known hazardous items and applicable items shown in FED-STD-313, Tables I and II. The SDS shall have any applicable identification number, such as National Stock Number or Special Item Number. A copy of the SDS shall be mailed or e-mailed no later than five (5) days prior to contractual delivery of items:

FAR clause 52.223-3, Hazardous Material Identification and Material Safety Data

SPECIAL PACKAGING INSTRUCTIONS RETRIEVAL & EXCHANGE SYSTEM

(SPIRES)

Contractors may request the use of SPIRES website to view item packaging requirements or search for Special Packaging Instruction drawings via the following website: https://lts.cce.af.mil/SPIRES/.

REUSABLE CONTAINERS

The contractor shall safeguard all received reusable shipping containers that meet the requirements of the AFMC Form 158 and are suitable for return shipment of serviceable assets. The contractor shall dispose of and replace unserviceable containers with new containers that meet requirements of the AFMC Form 158.

Contact the Product Support Manager and Administering Contracting Office (ACO) for disposition instructions and replacement when Long Life Reusable Container(s) are received in an unserviceable condition.

REPORTING DISCREPANCIES

The contractor shall use Web Supply Discrepancy Report (WebSDR) to submit/reply to a Supply Discrepancy Report (SDR), when improperly packed assets are received/shipped in other than the contracted packaging requirements (coded data or Special Packaging Instructions (SPI) drawings) from Department of Defense (DoD) components or contractor activities. The contractor shall request a WebSDR account via the following website: https://www.transactionservices.dla.mil/daashome/homepage.asp

(See Defense Logistics Management (DLM) 4000.25-M, Volume 2, Supply Standard and Procedures, Chapter 17, Supply Discrepancy Reporting) http://www.dla.mil/HQ/InformationOperations/DLMS/

Exceptions when no damage has occurred are as follows:

- Items packaged before the current SPIdate.

- An alternate pack may be used, provided the prime Air Force Sustainment Complex, Packaging Office at the Air Logistics Complex (ALC) approves and issues a waiver, deviation number, which would be annotated on the exterior container on the lower right hand portion of the identification side of the container.

- In accordance with Technical Order (TO) 00-85B-3, How to Package Air Force Spares, the contractor may substitute the next larger size fast pack, of the type I or type II to ship transportation priorities 1 and 2 shipments as long as there is no decrease in any of the container dimensions without the requirement of a waiver deviation. TO 00- 85B-3, para 4.2 can be accessed via the website:

- https://www.tinker.af.mil/Portals/106/Documents/Technical%20Orders/AFD-082416-00-85B-3.pdf

ASSIST Documents for Specifications Listed in the GSA Index of Federal Specifications, Standards and Commercial Item Descriptions The contractor shall use the ASSIST website to access specification, standards, data item descriptions documents listed in this contract solicitation:

FAR 52-211-2 Availability of Specifications, Standards, and Data Item Descriptions listed in the Acquisition Streamlining and Standardization Information System https://quicksearch.dla.mil/

AFSC

406 SCMS/GULAA

Attn: Keith Restorff

DSN: 777-9192

COMM: 801-777-9192

E-mail: keith.restorff@us.af.mil

APPLICABLE GOVERNMENT PACKAGING DOCUMENTS

NOTE: UTILIZE THE MOST RECENT REVISION

AFI 24-602V2_AFGM2018-01, Preparation and Movement of Air Force Cargo

AFMAN 24-204, Preparing Hazardous Materials for Military Air Shipments

DLMS 4000.25, Defense Logistics Management Systems, Volume 2, Change 10, Supply Standards and Procedures, Chapter 17, Supply Discrepancy Reporting

DOT Title 29, Occupational Safety and Health Administration, Labor

DOT Title 49, Code of Federal Regulations (49 CFR), Transportation

International Civil Aviation Organization (ICAO) Technical Instructions

International Air Transport Association (IATA) Dangerous Goods Regulation

International Maritime Dangerous Goods (IMDG) Code

ISPM 15, International Standard Phytosanitary Measure Note: Marking Requirements may be found in the American Lumber Standards Committee, Incorporated Wood Packaging Material Enforcement Regulations dated November 07, 2014 and ISPM 15.

MIL-STD-2073-1E, Change 3, Standard Practice, for Military Packaging

MIL-STD-129R, Change 1, Department of Defense Standard Practice Military Marking for Shipment and Storage

MIL-STD-648E, Department of Defense Design Criteria Standard, Specialized Shipping Containers

MIL-STD-147E, Change 1, Palletized Unit Loads

MIL-STD-1686C, Electrostatic Discharge Control Program for Protection of Electrical and Electronic Parts, Assemblies and Equipment (Excluding Electrically Initiated Explosive Devices) TO 00-85B-3, How to Package Air Force Spares

FED-STD-313E, Federal Standard: Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities

MIL-STD-1686C, Electrostatic Discharge Control Program for Protection of Electrical and Electronic Parts, Assemblies and Equipment (Excluding Electrically Initiated Explosive Devices).

DISTRIBUTION STATEMENT D: DISTRIBUTION AUTHORIZED TO DEPARTMENT OF DEFENSE AND U.S. DOD CONTRACTORS ONLY, ADMINISTRATIVE OR OPERATIONAL USE, 29 MARCH 2018. OTHER REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO 406

SCMS/GULAA, (PACKAGING DIVISION), HILL AFB, UTAH 84056.

DESTRUCTION NOTICE: FOLLOW THE PROCEDURES IN DOD 5220.22-M, NATIONAL INDUSTRIAL SECURITY PROGRAM OPERATING MANUAL (NISPOM), SECTION 5-705, OR DOD 5200.1-R, INFORMATION SECURITY PROGRAM, CHAPTER VI. FOR UNCLASSIFIED, LIMITED DOCUMENTS, DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF CONTENTS OR RECONSTRUCTION OF THE DOCUMENT.

AutoCAD SHX Text

82 LBS

ITEM WT.

2169 MOD

MARCH 87

DD

FORM

LEVEL B:

LEVEL A:

CLOSURE

IAW: ASTM D6251 (UNNAILED)

IAW: ASTM D6251 (UNNAILED)

COMPUTER GENERATED

SPI NO. F01-505-7532

CODE ID

98747

DESIGN FRAGILITY G

SPEC STYLE TYPE CL VRTY GR TR

AS SPECIFIED BELOW AND BILL OF MATERIALS

ILL.

NATIONAL STOCK NO.

PART OR DRAWING NO.

CURRENT

SPECIAL MARKINGS:

A) SPI NO. F01-505-7532

PRESERVATIVE: N/A

UNSERVICEABLE METHOD: GX

CLEANING & DRYING: IAW MIL-STD-2073

MILITARY PRESERVATION IAW MIL-STD-2073

B) REUSABLE CONTAINER & DUNNAGE DO NOT DESTROY.

MARKING IAW MIL-STD-129

QUP

ICQ

CNTR O.D.

ITEM DIM

CNTR I.D.

GROSS WT LBS

ITEM NOMENCLATURE

PACKING

LEVEL

GROSS CU FT

B

A

ASTM D6251

ASTM D6251

REV

DATE

ORIGINAL

CHK.

AUTH.

P.S.

SPECIAL PACKAGING INSTRUCTION

35 1/2

35 1/2

23 1/2

17 3/4

17 3/4

5 1/4

LENGTH WIDTH DEPTH

33 1/2

33 1/2

12 1/4

12 1/4

LEVEL A LEVEL B

10.940

III

10.940

SPI NO. (TPO)

SHEET 1 OF 5

D. NAY K. RESTORFF S. PEELER N. CORONADO

6130-01-505-7532 WF

CW2501ML

F01-505-7532

B

08182

REVISIONS

DESCRIPTION

LTR

DATE

MARK THE SPI NUMBER ON THE IDENTIFICATION SIDE OF CONTAINER.

III

SERVICEABLE METHOD: GX

C) ESD LABELS

CHANGED DIMENSIONS, ADDED DISTRIBUTION STATEMENT AND DESTRUCTION NOTICE

18092

REQD

P/N

QTY

SIZE: (INCHES UNLESS SPECIFIED) TOLERANCES ON FRAC. ± , 18, DECIMAL ± .10, ANGLES ± 1°

DESCRIPTION

NOMENCLATURE OR

SPECIFICATION

MATERIAL

2 1 1 2 1 2 1 1 2 2 2 2 2 2

STRAPPING, STEEL PAD, FRONT PAD, END PAD, SIDE WRAP PAD, TOP & BOTTOM CONTAINER, INTERIOR BAG, BARRIER CUSHION, END CUSHION, SIDE CUSHION, TOP & BOTTOM CLEAT, FILLER EDGE CLEAT, THRU EDGE SKID

3/4 X .015 X AS REQUIRED 17 X 2 1/2 X 2 20 1/2 X 6 1/4 X 1/2 22 X 6 1/4 X 1 1/8 51 X 31 25 X 20 1/2 X 1/8 25 X 20 1/2 X 6 1/2 (ID) 38 X 31 (ID) 22 X 8 1/4 X 3 1/2 33 1/4 X 8 1/4 X 3 33 1/4 X 28 X 2 1 X 3 (NOM) X 22 3/4 1 X 3 (NOM) X 33 4 X 4 (NOM) X 30

ASTM D3953 TYPE 1, RD, FINISH A A-A-59136 CLASS 1, GRADE B ASTM D4727 CF, DOM, GRADE 200 ASTM D4727 CF, DOM, GRADE 200 MIL-PRF-81705 TYPE III, CLASS 1 ASTM D4727 CF, DOM, GRADE 200 ASTM D5118 RSC, CF, DOM, SW, GRADE 200 MIL-DTL-117 TYPE I, CLASS F, STYLE 1 MIL-PRF-26514 TYPE III, CLASS 2, GRADE B MIL-PRF-26514 TYPE III, CLASS 2, GRADE B MIL-PRF-26514 TYPE III, CLASS 2, GRADE B ASTM D6199 CLASS 2 ASTM D6199 CLASS 2 ASTM D6199 CLASS 2

-14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1

2169C MOD

SHEET 2 OF 5

CAUTION NOTICES

NOTICE 1: ASSETS PACKAGED IN ACCORDANCE WITH PREVIOUS EDITIONS OF THIS SPI DO NOT REQUIRE

REPACKAGING IF THE INTEGRITY OF THE SPI IS MAINTAINED.

NOTICE 2: SEE SPIRES FOR A COMPLETE LISTING OF NSN's ASSIGNED TO THIS SPI.

NOTICE 3: PACKAGING MATERIAL MAY BE SUBSTITUTED IF IT MEETS THE REQUIREMENTS OF MIL-STD-2073, PROVIDES EQUAL OR BETTER PROTECTION AND THERE IS NO INCREASED COST TO THE GOVERNMENT.

NOTICE 4: OVERSEAS AND FMS PACKAGING MUST MEET THE REQUIREMENTS OF LEVEL A PACKAGING.

INTERNATIONAL STANDARDS FOR PHYTOSANITARY MEASURES

REVISION OF ISPM NO. 15

REVISION OF WOOD PACKAGING MATERIAL FOR INTERNATIONAL TRADE

THE FOLLOWING STATEMENT IS IN COMPLIANCE WITH THE UNITED NATIONS-IMPLEMENTED RESTRICTIONS ON WOOD

PACKAGING MATERIAL (WPM). THIS REQUIREMENT IS SPECIFICALLY CONCERNED WITH INVASIVE SPECIES SUCH AS THE

PINEWOOD NEMATODE. WPM IS DEFINED AS WOOD PALLETS, SKIDS, LOAD BOARDS, PALLET COLLARS, WOODEN BOXES, REELS, DUNNAGE, CRATES, FRAMES, AND CLEATS. THE STATEMENT BELOW CITES THE REQUIREMENTS IN DETAIL AND

COVERS LUMBER FOR BUILDING CONTAINERS AND PALLETS USED FOR DELIVERIES, RESULTING IN SHIPMENTS WORLDWIDE

(DIRECT, OR THROUGH AIR LOGISTICS CENTERS (ALC), CONTAINER CONSOLIDATION POINTS (CCP), OR OTHER BASES).

WOODEN LUMBER, WOODEN PALLET AND PACKAGING/CONTAINER STATEMENT:

ALL WOODEN LUMBER, WOODEN PALLETS, AND WOODEN CONTAINERS PRODUCED ENTIRELY OR IN PART OF WOOD

PACKAGING MATERIAL (WPM) SHALL BE CONSTRUCTED FROM DEBARKED WOOD IN ADDITION TO THE APPLICATION OF

HEAT-TREATED (HT) MATERIAL (HT TO 56 DEGREES CENTIGRADE OR 133 DEGREES FAHRENHEIT FOR 30 MINUTES).

CERTIFICATION/MARKING IS REQUIRED BY AN ACCREDITED AGENCY RECOGNIZED BY THE AMERICAN LUMBER STANDARDS

COMMITTEE (ALSC). FOR REFERENCE DOCUMENTATION, SEE LATEST REVISION OF "INTERNATIONAL STANDARDS FOR

PHYTOSANITARY MEASURES (ISPM NO. 15), "REGULATION OF WOOD PACKAGING MATERIAL IN INTERNATIONAL TRADE."

NOTES

1. USE ADHESIVE A-A-59692, TYPE II OR EQUAL TO REACH REQUIRED THICKNESS OF REF.-11, -12 AND -13. USE OF

DOUBLE WALL IS AUTHORIZED TO USE FOR REF.-11 AND -12.

SHEET 3 OF 5

SHEET 4 OF 5

-11

-12

-10

-9

-13

-8

-7

ITEM REFERENCE

DIRECTION

OF

FLUTE

TYP.

-9

UNNAILED CLOSURE

FLIP LID OVER FOR ASSEMBLY

-4

-3

-2

-5

-6

-4

-14

-1

INNER CONTAINER

INSET SKIDS 2 " 12" FROM ENDS.

SHEET 5 OF 5

-7

Sheets and Views

015057532-SHEET 01

015057532-SHEET 02

015057532-SHEET 03

015057532-SHEET 04

015057532-SHEET 05