3215-1001 data.pdf
PDF 170 KB Posted
- Attached to
- 1/8" PVC SHEET Federal contract opportunity
- Solicitation number
- SPMYM2-23-Q-2006
About this file
This document provides ordering data for plastic sheet and sheeting materials to be procured under Defense Logistics Agency Land and Maritime solicitation number SPMYM2-23-Q-2006. The agency requires 1/8 inch solid colored gray polyvinyl chloride (PVC) sheet with a high polish finish and Level A packaging. The plastic material must meet specifications for composition, dimensions and tolerances, color, transparency, finish, suitability for explosives, and packaging and packing levels as outlined in the ordering data standard L-P-535E. The successful bidder will provide PVC sheet meeting these requirements for the Defense Logistics Agency Land and Maritime.
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| SPMYM2-23-Q-2006.pdf |
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
MATERIAL ORDERING DATA
L-P-535
IDN: N4523A 3215-1001
ICN: 38MNF63501 KO: S01 KOI: 005
Paragraph 6.2 Ordering Data
A. L-P-535E, PLASTIC SHEET (SHEETING) PLASTIC STRIP; POLY (VINYL CHLORIDE) AND
POLY VINYL CHLORIDE-VINYL ACTATE) RIGID, dated 27 APR 1979. NOTICE 4 dated 20 JUN 2012.
B. Composition A, Poly (Vinyl Chloride Type, Class as Applicable:
TYPE 1 - Normal impact strength, high stiffness and chemical resistance
Class 1 - Maximum stiffness and maximum chemical resistance
Class 2 - Maximum stiffness and high chemical resistance
Class 3 - High stiffness and maximum chemical resistance
TYPE II - High impact strength, moderate chemical resistance
Grade NT - Nontoxic according to intended use
Grade GU – General use
TYPE III - Medium impact strength, low chemical resistance
TYPE IV - Good embossing characteristics
Composition B – Poly (Vinyl Chloride-Vinyl Acetate)
TYPE I - Unmodified
Class 1 - Colored
Three-dimensional displays for educational purposes
Three -dimensional decorations
Class 2 - Colorless and transparent
Recording Discs
Class 3 - Optical quality
Transparent cartographic sheeting
TYPE II - Modified
Class 1 - Medium impact strength
Luminous ceilings
Spiral book bindings)
Class 2 - Moderately high impact strength
Decorative and structural wall panel laminates
Instrument dial covers
Class 3 – Very high impact strength
Bas-relief maps
Signs and Charts
Navigation and computing charts
Slide Rules
Identification Cards
Instrument dial faces
C. Oven heat stability requirements for specimens to pass: 3 specimens shall be tested in accordance with ASTM D2115.
Applicable D. Dimensions and form required: The nominal thickness and width shall be specified in the contract or purchase order (see 6.2). Unless otherwise specified, the permissible tolerances from the nominal dimensions shall be shown below:
Thickness:
Less than 2mm (0.08 in.) plus 20 percent, minus 20 percent 2 to 4mm (0.08 to 0.16 in) plus 15 percent, minus 15 percent Above 4 m (0.16 in.), plus 10 percent, minus 10 percent
Width: plus 6.4, -0mm (plus 0.25, -0 in.)
Length of sheet: plus 6.4, -lmn (plus 0.25, -0 in.)
Length of sheeting in roll: plus 4 percent, minus O percent
Squareness: Difference in lengths of the diagonals of the cut sheets shall be not greater than 6.4m (0.25 in.)
E. Color and transparency shall be specified by the procuring agency.
F. Finish desired: The sheet (sheeting) and strip' shall be furnished with a high polish, matte, grained, or special finish as specified in the contract. Select which one.
G. Suitability for use with explosives, is not required. If required a special test shall be conducted at a designated Government laboratory to determine compliance of the material in this respect (see 6. 3).
This test shall be requested by the procuring agency. Use drop down box if needed.
H. Selection of the applicable levels of packaging and packing (see 5.1 and 5.2) Packaging shall be level A as specified (see 6.2), (Use drop down box) Packing shall be Level A.
Additional Data Requirements: Paragraph E. Per PSNS&IMF ordering document (JML) solid colored GRAY PVC Sheet is required
Prepared By: Alan Orr Code: 250VP
File details come from the government source that posted it. Updated .