23396019 - 2310-165 Rev A.pdf
PDF 384 KB Posted
- Attached to
- Adapter Straight Federal contract opportunity
- Solicitation number
- N4215823QE019
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| Synopsis - 1-04-23.doc | DOC document | |
| 23396019- Continuation Report.pdf | ||
| 23396020- Continuation Report.pdf | ||
| Solicitation N4215823QE019.pdf |
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
M. NAWAZ
(SOF) 09/05/06
J. BILLING
(SOF) 09/06/06
UNLESS OTHERWISE NOTED IN THE SKETCH, ALL DIMENSIONS ARE IN
INCHES.
A
THE WATERWAYS OF ALL FITTINGS SHALL HAVE A MAXIMUM SURFACE
ROUGHNESS OF 125 MICROINCHES.
THIS PLAN IS APPLICABLE ONLY WHEN REFERENCED BY A TECHNICAL
WORKING DOCUMENT (TGI, MIF, ETC.) OR STANDARD PROCEDURE (NP
MANUAL CHAPTER, PROCESS INSTRUCTION, ETC.). OTHER USES SHALL BE
AT THE DISCRETION OF THE USING SHOP.
MATERIAL FOR ANY FITTING SHALL BE AS SPECIFIED IN THE TECHNICAL
DOCUMENT INVOKING THIS PLAN OR BY THE COGNIZANT TECHNICAL
CODE. DIMENSIONS ARE SUITABLE FOR USE AT 150 PSIG WITH BRASS,
MILD STEEL, 300 SERIES CRES, NICU & CUNI.
UNLESS OTHERWISE SPECIFIED
GEOMETRIC TOLERANCES
SYM
A
B
PARALLELISM
SURFACE FINISH
TRUE POSITION
CONCENTRICITY
PERPENDICULAR
FLATNESS
GEOMETRY
C 7.
6.
5.
OI
DO NOT SCALE DRAWING
±.015
±.010
±.005
3 PL
UNLESS OTHERWISE SPECIFIED
DIMENSIONAL TOLERANCES
24" & OVER
6" TO 24"
UNDER 6"
DIMENSIONS
AS NOTED
AS NOTED
AS NOTED
AS NOTED
AS NOTED
AS NOTED
TOLERANCE
±.02
ANGULAR ±2°
±.03
±.01
2 PL
DECIMALS
REV
SHEET
±1/32
±1/16
±1/64
FRACTIONS
OF SHEETS
REVISION STATUS
OIOI
OIOIOI
NO
CODE
CODE
NORFOLK NAVAL SHIPYARD
CODE
APPROVED
REACTOR ENGINEERING DIVISION
REFERENCES
M. NAWAZ
THIS PLAN
DEVELOPED BY
EXT
BRANCH
CODE
CODE
CODE
HEAD
CODE
OIOI
CODE
DRAWN BY
PROJECT
ENGINEER
2310.5
6-8012
TITLE IDENT
HEAD, REACTOR ENGINEERING DIVISION
NO SCALE
2310-165
SCALE
DRAWING NO.
SHEET 1 OF 8
DATE
REV.
A
B
C
APPROVED BY
DRAWN BY
THIS DRAWING IS TAKEN FROM PRODUCTION ENGINEERING DRAWING
N-61036, ALT. H. IT HAS BEEN REDRAWN IN AUTOCAD.
FOR ANY ITEM, SHEET #1 & THE SHEET(S) REFERENCED IN THE TABLE OF
CONTENTS CONSTITUTE A COMPLETE PLAN FOR THAT ITEM.
ALTHOUGH THE DESIGN OF MANY FITTINGS ON THIS PLAN MAKE THEM SAFE
FOR USE AT HIGHER THAN 150 PSIG, FITTINGS ON THIS PLAN SHALL NOT BE
USED FOR WORKING PRESSURES EXCEEDING 150 PSIG WITHOUT SPECIFIC
APPROVAL OF THE COGNIZANT TECHNICAL CODE WHO WILL ASSUME FULL
RESPONSIBILITY FOR THEIR USE AT ELEVATED PRESSURES. IT IS
RECOMMENDED THAT THIS AUTHORIZATION BE SUBJECT TO BURST
PRESSURE CALCULATIONS BY THE COGNIZANT TECHNICAL CODE AND A
PRE-INSTALLATION HYDROSTATIC TEST OF EACH FITTING AT 150% OF
WORKING PRESSURE.
D
E
4.
3.
1.
2.
MNPT TO OD SIZE TUBE
SERRATED HOSE CONNECTORS
SERRATED HOSE TO
HOSE CONNECTORS
FNPT TO SERRATED
SPECIAL NPT SEALS
O-RING SEALED MNPT
TO AND10050 ADAPTER
HOSE CONNECTORS
OD SIZED TUBE TO SERRATED
NPT TO SERRATED HOSE
DESCRIPTION
ITEM
CONNECTORS
(O-RING)
CONNECTORS
REV
SHEET
REVISIONS
DESCRIPTION
D
E SHT. 3 of 8, INCORPORATED NECESSARY
CHANGES IN ACCORDANCE WITH
A
PRODUCTION DRAWING N-61036, ALT. J.
R. PERKINS (SOF) 11/03/03
W. WALKER (SOF) 10/28/03
J.C. BILLING (SOF) 10/28/03
A A
SEE NOTE 8SEE NOTE 21/16 X 45° CHAMFER
"B"
"A"
EXCEPT AS NOTED IN NOTE 3, RADIUS ALL CORNERS 1/64".
AT SHOP'S DISCRETION, THE HOSE END MAY BE BORED TO AN I.D. NOT TO
EXCEED DIMENSION "D" MINUS (-) 0.150" FOR A DEPTH NOT TO EXCEED
DIMENSION "X=A-B".
THE BAR DIAMETER IS THAT REQUIRED TO OBTAIN A HEX OF SIZE "K"
(STYLE-B ONLY).
CERTAIN PIECES MAY BE MADE IN STYLE-A FROM IPS PIPE. IF PIPE IS USED,
DIMENSION "D" SHALL BE THE O.D. OF THE PIPE (REQUIRES TECH. CODE
APPROVAL).
THE O-RING NUMBERS CORRESPONDS TO THE SAE-AS28775 O-RING SIZE.
DEPENDING ON THE RELATIVE SIZE OF THE NPT & TUBE SIZE, ANGLE MAY
BE REVERSED OR NON-EXISTANT.
THE MINIMUM NUMBER OF SERRATIONS IS 4 PER INCH; MAX. 6 PER INCH.
REMOVE BURRS AND/OR SHARP RAISED METAL FROM EDGES OF
SERRATIONS BUT DO NOT FLATTEN SERRATION EDGES.
MACHINE TWO (2) 1/2" WIDE WRENCH FLATS ON OPPOSITE SIDES. MIN.
WALL UNDER FLAT SHALL BE 0.055" (STYLE-A ONLY).
CUT DOWN THE DIA. OF NPT TO ACHIEVE COMPRESSION OF THE O-RING ON
THE FACE OF A FEMALE NPT FITTING (STYLE-B ONLY).
UNDERCUT TO THE DEPTH OF
THREAD FOR ONE THREAD WIDTH
1/16 X 45° CHAMFER
"H" NPT (SEE NOTE 1)
O-RING GROOVE IS
"N" WIDE & "P" DEEP
O-RING SIZE "R"
A
B
C
SEE NOTE 3
"A"
"C"
"L" "M"
"B"
"J"
STYLE-B
3/8
1/8
45° (SEE NOTE 4)
STYLE-A
"E"
2.
"D"
7.
9.
8.
SEE NOTE 8
6.
5.
4.
3.
"F" 1.
C
B
A
DRAWING NO.
SHEET 2 OF 8
2310-165 REV.
OI
CONNECTORS
ITEM 1 - NPT TO SERRATED HOSE
45° (SEE NOTE 4)
"C"D
E
"H" NPT
"F"
"E"
SEE NOTE 3
"D"
2 3
D
E
4 5
DIMENSIONS FOR ITEM 1
SIZE STYLE-B ONLY
NPT HOSE
I.D.
A +/- 1/8"
B +/- 1/16" C D E F H
J K L
+1/64 -0
M +0.000 -0.005
N P R (I.D. X O.D.)
BAR
DIA.
O-RING NO.
(NOTE 5)
1/4 1/4 2-5/8 1-1/8 0.540 0.290 0.250 3/32 1/4 3/8 1 1 0.755 0.140/0.145 0.081/0.083 0.549 x 0.755 1-1/8 113
1/4 3/8 2-5/8 1-1/8 0.540 0.400 0.375 7/32 1/4 3/8 1 1 0.755 0.140/0.145 0.081/0.083 0.549 x 0.755 1-1/8 113
1/4 1/2 2-5/8 1-1/8 0.540 0.535 0.500 5/16 1/4 3/8 1 1 0.755 0.140/0.145 0.081/0.083 0.549 x 0.755 1-1/8 113
3/8 1/4 2-5/8 1-1/8 0.675 0.290 0.250 1/8 3/8 13/32 1-1/4 1-1/4 0.943 0.140/0.145 0.081/0.083 0.737 x 0.943 1-1/2 116
3/8 3/8 2-5/8 1-1/8 0.675 0.400 0.375 7/32 3/8 13/32 1-1/4 1-1/4 0.943 0.140/0.145 0.081/0.083 0.737 x 0.943 1-1/2 116
3/8 1/2 2-5/8 1-1/8 0.675 0.535 0.500 13/32 3/8 13/32 1-1/4 1-1/4 0.943 0.140/0.145 0.081/0.083 0.737 x 0.943 1-1/2 116
3/8 3/4 3 1-1/8 0.675 0.800 0.750 13/32 3/8 13/32 1-1/4 1-1/4 0.943 0.140/0.145 0.081/0.083 0.737 x 0.943 1-1/2 116
1/2 1/2 2-5/8 1-1/8 0.840 0.535 0.500 13/32 1/2 17/32 1-1/2 1-1/2 1.068 0.140/0.145 0.081/0.083 0.862 x 1.068 1-1/2 118
1/2 3/4 3 1-1/8 1.050 0.800 0.750 1/2 1/2 17/32 1-1/2 1-1/2 1.068 0.140/0.145 0.081/0.083 0.862 x 1.068 1-1/2 118
1/2 1/4 2-5/8 1-1/8 0.840 0.290 0.250 3/32 1/2 17/32 1-1/2 1-1/2 1.068 0.140/0.145 0.081/0.083 0.862 x 1.068 1-1/2 118
1/2 3/8 2-5/8 1-1/8 0.840 0.400 0.375 7/32 1/2 17/32 1-1/2 1-1/2 1.068 0.140/0.145 0.081/0.083 0.862 x 1.068 1-1/2 118
1/2 1 3-1/4 1-1/8 0.840 1.050 1.000 1/2 1/2 17/32 1-1/2 1-1/2 1.068 0.140/0.145 0.081/0.083 0.862 x 1.068 1-1/2 118
1/2 1-1/4 5 2 0.840 1.310 1.250 1/2 1/2 1-7/32 1-1/2 1-1/2 1.375 0.140/0.145 0.081/0.083 0.862 x 1.068 1-1/2 118
1/2 1-1/2 5 2 0.840 1.560 1.500 1/2 1/2 1-7/32 1-1/2 1-1/2 1.068 0.140/0.145 0.081/0.083 0.862 x 1.068 1-3/4 118
1/2 2 5-1/2 2 0.840 2.080 1.995 1/2 1/2 1-7/32 1-1/2 1-1/2 1.068 0.140/0.145 0.081/0.083 0.862 x 1.068 2-1/2 118
3/4 3/4 3 1-1/8 1.050 0.800 0.750 19/32 3/4 9/16 1-1/2 1-1/2 1.318 0.140/0.145 0.081/0.083 1.112 x 1.318 1-3/4 122
3/4 1 3-1/4 1-1/8 1.315 1.050 1.000 5/8 3/4 9/16 1-1/2 1-1/2 1.318 0.140/0.145 0.081/0.083 1.112 x 1.318 1-3/4 122
1 1 3-1/4 1-1/4 1.315 1.050 1.000 23/32 1 21/32 1-3/4 1-3/4 1.568 0.140/0.145 0.081/0.083 1.362 x 1.586 2-1/4 126
1 1-1/4 4-1/4 1-1/4 1.315 1.310 1.250 7/8 1 21/32 1-3/4 1-3/4 1.568 0.140/0.145 0.081/0.083 1.362 x 1.586 2-1/4 126
1 1-1/2 5 1-1/4 1.315 1.560 1.500 7/8 1 21/32 1-3/4 1-3/4 1.568 0.140/0.145 0.081/0.083 1.362 x 1.586 2-1/4 126
1-1/4 1-1/4 5 2 1.660 1.310 1.250 1 1-1/4 1 2-1/16 2-1/16 1.880 0.140/0.145 0.081/0.083 1.674 x 1.880 2-1/2 131
1-1/4 1-1/2 5 2 1.660 1.560 1.500 1-1/8 1-1/4 1 2-1/16 2-1/16 1.880 0.140/0.145 0.081/0.083 1.674 x 1.880 2-1/2 131
1-1/4 1 5 2 1.660 1.050 1.000 3/4 1-1/4 1 2-1/16 2-1/16 1.880 0.140/0.145 0.081/0.083 1.674 x 1.880 2-1/2 131
1-1/4 2 5-1/2 2 1.660 2.080 1.995 1-1/2 1-1/4 1 2-1/16 2-1/16 2.070 0.140/0.145 0.081/0.083 1.674 x 1.880 2-1/2 131
1-1/2 1-1/4 5-1/8 2-1/8 1.900 1.310 1.250 1 1-1/2 1-1/16 2-3/8 2-3/8 2.131 0.140/0.145 0.081/0.083 1.925 x 2.131 3 135
1-1/2 1-1/2 5-1/8 2-1/8 1.900 1.560 1.500 1-1/4 1-1/2 1-1/16 2-3/8 2-3/8 2.131 0.140/0.145 0.081/0.083 1.925 x 2.131 3 135
1-1/2 3/4 4-1/4 2-1/8 1.900 0.800 0.750 19/32 1-1/2 1-1/16 2-3/8 2-3/8 2.131 0.140/0.145 0.081/0.083 1.925 x 2.131 3 135
1-1/2 2 5-5/8 2-1/8 1.900 2.080 1.995 1-1/4 1-1/2 1-1/16 2-3/8 2-3/8 2.131 0.140/0.145 0.081/0.083 1.925 x 2.131 3 135
2 1-1/2 5-1/4 2-1/4 2.375 1.560 1.500 1-1/4 2 1-1/16 2-7/8 2-7/8 2.631 0.140/0.145 0.081/0.083 2.425 x 2.631 3-1/2 143
2 2 5-3/4 2-1/4 2.375 2.080 1.995 1-1/2 2 1-1/16 2-7/8 2-7/8 2.631 0.140/0.145 0.081/0.083 2.425 x 2.631 3-1/2 143
"K"
DIMENSIONS FOR ITEM 2
Size Size
Hard Tube Hose ID
A +/- 1/8"
B +/- 1/16" C D E F G H Hard
Tube Hose
ID
A +/- 1/8"
B +/- 1/16" C D E F G H
1/4 1/4 2-1/2 3/4 0.250 0.290 0.250 0.125 3/32 1-1/2 1-1/4 1/4 4-1/4 2 1.250 0.290 0.250 1.000 3/32 1-1/2 1/4 3/8 2-1/2 3/4 0.250 0.400 0.375 0.125 1/8 1-1/2 1-1/4 3/8 4-1/4 2 1.250 0.400 0.375 1.000 7/32 1-1/2 1/4 1/2 2-1/2 3/4 0.250 0.535 0.500 0.125 1/8 1-1/2 1-1/4 1/2 4 2 1.250 0.535 0.500 1.000 11/32 1-1/4 3/8 1/4 3-1/8 1-1/8 0.375 0.290 0.250 0.250 3/32 1-1/2 1-1/4 3/4 4-3/8 2 1.250 0.800 0.750 1.000 15/32 1-3/4 3/8 3/8 3-1/8 1-1/8 0.375 0.400 0.375 0.250 7/32 1-1/2 1-1/4 1 5 2 1.250 1.050 1.000 1.000 23/32 2-1/2 3/8 1/2 2-7/8 1-1/8 0.375 0.535 0.500 0.250 1/4 1-1/2 1-1/4 1-1/4 5-3/8 2 1.250 1.310 1.250 1.000 1 3 1/2 1/4 3-1/2 1-1/8 0.500 0.290 0.250 0.375 3/32 1-1/2 1-1/4 1-1/2 6 2 1.250 1.560 1.500 1.000 1 3-1/2 1/2 3/8 2-7/8 1-1/8 0.500 0.400 0.375 0.375 7/32 1-1/2 1-1/2 1/4 4-3/4 2-1/4 1.500 0.290 0.250 1.250 3/32 1-1/2 1/2 1/2 3-1/8 1-1/8 0.500 0.535 0.500 0.375 11/32 1-1/2 1-1/2 3/8 4-3/4 2-1/4 1.500 0.400 0.375 1.250 7/32 1-1/2 1/2 3/4 3-1/4 1-3/4 0.500 0.800 0.750 0.375 15/32 1-3/4 1-1/2 1/2 4-3/8 2-1/4 1.500 0.535 0.500 1.250 11/32 1-1/4 1/2 1 3-1/2 1-3/4 0.500 1.050 1.000 0.375 23/32 2-1/2 1-1/2 3/4 4-3/4 2-1/4 1.500 0.800 0.750 1.250 15/32 1-3/4 3/4 1/4 3-1/4 1-1/4 0.750 0.290 0.250 0.625 3/32 1-1/2 1-1/2 1 5-3/8 2-1/4 1.500 1.050 1.000 1.250 23/32 2-1/2 3/4 3/8 3-1/4 1-1/4 0.750 0.400 0.375 0.625 7/32 1-1/2 1-1/2 1-1/4 5-3/4 2-1/4 1.500 1.310 1.250 1.250 1 3 3/4 1/2 3 1-1/4 0.750 0.535 0.500 0.578 11/32 1-1/2 1-1/2 1-1/2 6-1/4 2-1/4 1.500 1.560 1.500 1.250 1-1/4 3-1/2 3/4 3/4 3-1/4 1-1/4 0.750 0.800 0.750 0.578 15/32 1-3/4 2 1/4 5-3/4 3 2.000 0.290 0.250 1.700 3/32 1-1/2 3/4 1 4-1/4 1-1/4 0.750 1.050 1.000 0.578 23/32 2-1/2 2 3/8 5-3/4 3 2.000 0.400 0.375 1.700 7/32 1-1/2 1 1/4 3-3/4 1-1/2 1.000 0.290 0.250 0.875 3/32 1-1/2 2 1/2 5-1/2 3 2.000 0.535 0.500 1.700 11/32 1-1/4 1 3/8 3-3/4 1-1/2 1.000 0.400 0.375 0.875 7/32 1-1/2 2 3/4 5-3/4 3 2.000 0.800 0.750 1.700 15/32 1-3/4 1 1/2 3-1/4 1-1/2 1.000 0.535 0.500 0.828 11/32 1-1/4 2 1 6-3/8 3 2.000 1.050 1.000 1.700 23/32 2-1/2 1 3/4 3-3/4 1-1/2 1.000 0.800 0.750 0.828 15/32 1-3/4 2 1-1/4 6-3/4 3 2.000 1.310 1.250 1.700 1 3 1 1 4-1/4 1-1/2 1.000 1.050 1.000 0.828 23/32 2-1/2 2 1-1/2 7 3 2.000 1.560 1.500 1.700 1-1/4 3-1/2 1 1-1/4 5 1-1/2 1.000 1.310 1.250 0.828 7/8 3 2 2 7 3 2.000 2.060 1.995 1.700 1-1/2 3-1/2 1 1-1/2 5-5/8 1-1/2 1.000 1.560 1.500 0.828 7/8 3-1/2 1-1/2 2 6-1/4 2-1/4 1.500 2.060 1.995 1.250 1-1/4 3-1/2
1-1/4 2 6 2 1.250 2.060 1.995 1.000 1 3-1/2
A
CONNECTORS
"B"
SERRATED HOSE
ITEM 2 - OD SIZED TUBE TO
A
B
C
D
E
"H" (SEE NOTE 1)
30° (SEE NOTE 2)
3 4 5
2310-165
DRAWING NO.
REV.
2 3 4 5
A
B
C
D
E
A
A
A
CONNECTORS
SERRATED HOSE
ITEM 2 - OD SIZED TUBE TO
A
B
C
D
E
"H" (SEE NOTE 1)
30° (SEE NOTE 2)
3 4 5
SHEET 3 OF 8
2310-165 REV.
2 3 4 5
A
B
C
D
E
A
A
AA
AA
AA
1. THE MINIMUM NUMBER OF SERRATIONS IS 4 PER INCH, MAX. 6 PER INCH.
REMOVE ANY BURRS AND/OR SHARP RAISED METAL FROM EDGES OF
SERRATIONS BUT DO NOT FLATTEN SERRATION EDGES.
2. DEPENDING ON THE RELATIVE SIZE OF THE ENDS, ANGLE MAY BE
REVERSED OR NON-EXISTANT.
3. EXCEPT AS NOTED IN NOTE 1, RADIUS ALL CORNERS 1/64".
"B"
1/16 X 45° CHAMFER
"N"
"E" A
B
C
"C"
1/8"
45°
"D"
"A" THREADS
(SEE NOTE 2)
UNDERCUT TO
BASE OF THREAD
FOR WIDTH OF
ONE THREAD
1/16 X 45° CHAMFER
"L"
SEE O-RING
GROOVE DETAIL
O-RING SIZE "P"
"M"
"B" THREADS
O-RING SIZE "R"
1/16"
3/8"
45°
"K"
THE HEX (E) EXCEEDS THE STANDARD SIZES FOR HEX'S.
REMOVE ALL BURRS AND RADIUS ALL CORNERS 1/64".
DIMENSION "X" IS THE APPROXIMATE OVERALL LENGTH (FOR MATERIAL
ESTIMATE ONLY).
THE O-RING NUMBERS CORRESPONDS TO THE SAE-AS28775 O-RING SIZE.
CUT DOWN DIA. OF NPT TO ACHIEVE COMPRESSION OF THE O-RING ON THE
FACE OF A FEMALE NPT FITTING.
SIZES ARE GIVEN AS NPT SIZE THEN TUBE SIZE FOR AND10050.
TO AND10050 ADAPTER
ITEM 3 - O-RING SEALED MNPT
1.
6.
5.
4.
3.
2.
D
E
1 2 3
C
B
AO-RING GROOVE DETAIL
"H"
"F" 32
2310-165
SHEET 4 OF 8
DRAWING NO.
REV. OI
E
D
4 5
DIMENSIONS FOR ITEM 3
P R
SIZE A (NPT) B (STRAIGHT
THREAD) C
D +1/64
-0 E F
G +0.000 -0.005
H J +/-0.015 K L
M +.015 -.000
N +1/16
-0 I.D. x O.D. SIZE NO.
(NOTE 3) I.D. x WALL O-RING NO.
(NOTE 3)
X
(NOTE 4)
1/4 x 1/4 1/4 7/16 - 20 3/8 15/16 1 0.145/0.140 0.755 0.083/0.081 0.364 3/16 13/32 0.075 11/16 0.549 x 0.755 113 0.351 x 0.072 904 1-3/8
1/4 x 3/8 1/4 9/16 - 18 3/8 15/16 1 0.145/0.140 0.755 0.083/0.081 0.481 9/32 15/32 0.083 13/16 0.549 x 0.755 113 0.468 x 0.078 906 1-3/8
3/8 x 3/8 3/8 9/16 - 18 13/32 1-1/8 1-1/4 0.145/0.140 0.945 0.083/0.081 0.481 9/32 15/32 0.083 13/16 0.737 x 0.943 116 0.468 x 0.078 906 1-3/8
3/8 x 1/2 3/8 3/4 - 16 13/32 1-1/8 1-1/4 0.145/0.140 0.945 0.083/0.081 0.660 25/64 15/32 0.094 1 0.737 x 0.943 116 0.644 x 0.087 908 1-3/8
1/2 x 1/2 1/2 3/4 - 16 17/32 1-5/16 1-1/2 0.145/0.140 1.068 0.083/0.081 0.660 13/32 15/32 0.094 1 0.862 x 1.068 118 0.644 x 0.087 908 1-1/2
3/4 x 3/8 3/4 9/16 - 18 11/16 1-1/2 1-5/8 0.145/0.140 1.318 0.083/0.081 0.481 9/32 15/32 0.083 13/16 1.112 x 1.318 122 0.468 x 0.078 906 1-5/8
3/4 x 1/2 3/4 3/4 - 16 11/16 1-1/2 1-5/8 0.145/0.140 1.318 0.083/0.081 0.660 25/64 15/32 0.094 1 1.112 x 1.318 122 0.644 x 0.087 908 1-5/8
3/4 x 3/4 3/4 1-1/16 - 12 11/16 1-1/2 1-5/8 0.145/0.140 1.318 0.083/0.081 0.945 19/32 9/16 0.125 1-3/8 1.112 x 1.318 122 0.924 x 0.116 912 1-5/8
3/4 x 1 3/4 1-5/16 - 12 11/16 1-1/2 1-5/8 0.145/0.140 1.318 0.083/0.081 1.195 5/8 9/16 0.125 1-5/8 1.112 x 1.318 122 1.171 x 0.116 916 1-5/8
1 x 3/8 1 9/16 - 18 7/8 1-3/4 2 0.145/0.140 1.568 0.083/0.081 0.481 9/32 15/32 0.083 13/16 1.362 x 1.568 126 0.468 x 0.078 906 1-5/8
1 x 1/2 1 3/4 - 16 7/8 1-3/4 2 0.145/0.140 1.568 0.083/0.081 0.660 25/64 15/32 0.094 1 1.362 x 1.568 126 0.644 x 0.087 908 1-5/8
1 x 3/4 1 1-1/16 - 12 7/8 1-3/4 2 0.145/0.140 1.568 0.083/0.081 0.945 19/32 9/16 0.125 1-3/8 1.362 x 1.568 126 0.924 x 0.116 912 1-3/4
1 x 1 1 1-5/16 - 12 7/8 1-3/4 2 0.145/0.140 1.568 0.083/0.081 1.195 51/64 9/16 0.125 1-5/8 1.362 x 1.568 126 1.171 x 0.116 916 1-3/4
1 x 1-1/4 1 1-5/8 - 12 7/8 1-3/4 2 0.145/0.140 1.568 0.083/0.081 1.507 1-1/16 9/16 0.125 1-7/8 1.362 x 1.568 126 1.475 x 0.118 920 1-3/4
1 x 1-1/2 1 1-7/8 - 12 7/8 1-3/4 2-1/4 0.145/0.140 1.568 0.083/0.081 1.756 1-5/16 11/16 0.125 2-1/8 1.362 x 1.568 126 1.720 x 0.118 924 1-3/4
1 x 2 1 2-1/2 - 12 7/8 1-3/4 3 0.145/0.140 1.568 0.083/0.081 2.381 1-25/32 7/8 0.125 2-3/4 1.362 x 1.568 126 2.337 x 0.118 932 1-3/4
1-1/4 x 1 1-1/4 1-5/16 - 12 1-1/8 2-1/16 2-1/4 0.145/0.140 1.880 0.083/0.081 1.195 49/64 9/16 0.125 1-5/8 1.674 x 1.880 131 1.171 x 0.116 916 2-1/8
1-1/4 x 1-1/4 1-1/4 1-5/8 - 12 1-1/8 2-1/16 2-1/4 0.145/0.140 1.880 0.083/0.081 1.507 1-1/16 9/16 0.125 1-7/8 1.674 x 1.880 131 1.475 x 0.118 920 2-1/8
1-1/4 x 1-1/2 1-1/4 1-7/8 - 12 1-1/8 2-1/16 2-1/4 0.145/0.140 1.880 0.083/0.081 1.756 1-5/16 11/16 0.125 2-1/8 1.674 x 1.880 131 1.720 x 0.118 924 2-1/4
1-1/4 x 2 1-1/4 2-1/2 - 12 1-1/8 2-1/16 2-1/2 0.145/0.140 1.880 0.083/0.081 2.381 1-5/16 7/8 0.125 2-3/8 1.674 x 1.880 131 2.337 x 0.118 932 2-3/8
1-1/2 x 1 1-1/2 1-5/8 - 12 1-3/8 2-3/8 2-1/2 0.145/0.140 2.131 0.083/0.081 1.195 13/16 9/16 0.125 1-5/8 1.925 x 2.131 135 1.171 x 0.116 916 2-1/8
1-1/2 x 1-1/4 1-1/2 1-5/8 - 12 1-3/8 2-3/8 2-1/2 0.145/0.140 2.131 0.083/0.081 1.507 1-1/16 9/16 0.125 1-7/8 1.925 x 2.131 135 1.475 x 0.118 920 2-1/8
1-1/2 x 1-1/2 1-1/2 1-7/8 - 12 1-3/8 2-3/8 2-1/2 0.145/0.140 2.131 0.083/0.081 1.756 1-5/16 11/16 0.125 2-1/8 1.925 x 2.131 135 1.720 x 0.118 924 2-1/4
1-1/2 x 2 1-1/2 2-1/2 - 12 1-3/8 2-3/8 3 0.145/0.140 2.131 0.083/0.081 2.381 1-43/64 7/8 0.125 2-3/4 1.925 x 2.131 135 2.337 x 0.118 932 2-1/2
"J""G"
OI
2. THREAD THE SEAL ONTO THE MALE NPT, AS A TEFLON INSERTEDPLAN
"B"
A
B
BREAK
6. REPLACE THE O-RING AND MAKE UP THE JOINT.
SIDE OF THE SEAL WHICH DOES NOT CONTAIN THE O-RING GROOVE.
MANUAL P9505-4. THE BRAZING SHALL BE DONE FROM THE
MALE NPT USING A FACE FEED JOINT IN ACCORDANCE WITH NNSY
MATERIAL, "SEAL BRAZE" THE JOINT BETWEEN THE SEAL AND THE
5. REMOVE THE O-RING FROM THE SEAL. THEN, EXCLUDING FOREIGN
PIECE.
THE SEAL, THEN REMOVE THE MALE PIECE FROM THE FEMALE
4. MARK THE MALE PIECE TO INDICATE THE EXACT LOCATION OF
ALLOW SOME TURNING, TIGHTEN THE SEAL.
3. WITH THE MALE PIECE LOOSE ENOUGH IN THE FEMALE PIECE TO
FEMALE NPT.
JAM NUT IS INSTALLED, THEN THREAD THE MALE NPT INTO A
O-RING "F"
"E" NPT, CUT WITH FULL
LENGTH OF TAP
SECTION "A-A"
"D"
3 4
REV.2310-165
SHEET 5 OF 8
DRAWING NO.
4. THE O-RING NUMBERS CORRESPONDS TO THE SAE-AS28775 O-RING SIZE
ITEM 4 - SPECIAL NPT SEALS (O-RING)
3. REMOVE ALL BURRS AND RADIUS ALL CORNERS 1/64".
2. O-RINGS SHALL BE BUNA-N.
ON 304 OR 316 CRES, NICU ON NICU, ETC.)
MNPT THREADS TO WHICH IT IS BEING ATTACHED. (i.e., 300 SERIES CRES
1. SEAL BODY SHALL BE OF MATERIAL SIMILAR TO THAT OF THE ITEM WITH
NOTES
D
C
"A"
E
1. FABRICATE SEALS TO ABOVE DIMENSIONS.
"A"
2 3
INSTALLATION
4 5
A
B
D
C
E
DIMENSIONS FOR ITEM 4
SIZE
(NPT)
A +1/16
-0 B
+/-.006 C
+/-1/64 D E F (O.D. x I.D. x C.S.)
O-RING
No.
(Note 4)
1/4 7/8 0.691 1/4 0.050/0.054 1/4 0.691 x 0.551 x 0.070 015 3/8 1 0.816 1/4 0.050/0.054 3/8 0.816 x 0.676 x 0.070 017 1/2 1-5/16 1.004 1/4 0.050/0.054 1/2 1.004 x 0.864 x 0.070 020 3/4 1-1/2 1.254 1/4 0.050/0.054 3/4 1.254 x 1.114 x 0.070 024 1 1-13/16 1.504 1/4 0.050/0.054 1 1.504 x 1.364 x 0.070 028
1-1/4 2-3/16 1.880 5/16 0.074/0.080 1-1/4 1.880 x 1.674 x 0.103 131 1-1/2 2-3/8 2.131 5/16 0.074/0.080 1-1/2 2.131 x 1.925 x 0.103 135
2 2-7/8 2.631 5/16 0.074/0.080 2 2.631 x 2.425 x 0.103 143 2-1/2 3-1/2 3.262 3/8 0.101/0.107 2-1/2 3.262 x 2.984 x 0.139 234
"A" (O.D.)
"C"
45° (SEE NOTE 3)UNDERCUT TO DEPTH
OF THREAD FOR ONE
THREAD WIDTH
1/16 X 45° CHAM
"L"
1/16 X 45° CHAMFER
"H" NPT
SEE NOTE 1
"K"
A
B
(REF)
"A"
"B"
STYLE-B
"J"
3/8"
45°
"C"
1/8"
"G"
63 "E"
"D"
B
A
REMOVE ALL BURRS AND RADIUS ALL CORNERS 1/64".
THE BAR DIA. IS THAT REQUIRED TO OBTAIN A HEX OF SIZE "K". (STYLE-B
ONLY)
THE O-RING NUMBER CORRESPONDS TO THE SAE-AS28775 O-RING SIZE.
DEPENDING ON THE RELATIVE SIZE OF THE NPT & TUBE SIZE, ANGLE MAY
BE REVERSED OR NON-EXISTANT.
MACHINE TWO (2) 1/2" WIDE, WRENCH FLATS ON OPPOSITE SIDES. MIN.
WALL UNDER FLAT SHALL BE 0.055". (STYLE-A ONLY)
CUT DOWN THE DIA. OF NPT TO ACHIEVE COMPRESSION OF THE O-RING ON
THE FACE OF A FEMALE NPT FITTING. (STYLE-B ONLY)
4.
6.
5.
3.
2.
1.
OIREV.2310-165
SHEET 6 OF 8
DRAWING NO.
(REF)
CONNECTORS
ITEM 5 - MNPT TO OD SIZE TUBE
45° (SEE NOTE 3)
O-RING GROOVE IS
"N" WIDE AND "P" DEEP
O-RING SIZE "R"
"A"
"B"
"C"D
C
"F"
1/16 X 45° CHAMFER
E
"H" NPT
1/16 X 45° CHAM
"E"
"D"SEE NOTE 2
STYLE-A
"G"
2 3
E
C
D
4 5
DIMENSIONS FOR ITEM 5
SIZE STYLE-B ONLY
NPT TUBE
O.D.
A +1/8 -0
B
(REF) C D
+/-.005 E
+/-.005 F G +/-1/16 H J K
L +1/64
-0
M +0
-.005 N P R
(I.D. X O.D.)
BAR
DIA.
O-RING NO.
(NOTE 4)
1/4 1/4 2-3/8 1-1/8 0.540 0.250 0.180 3/32 1-1/4 1/4 3/8 1 1 0.755 0.140/0.145 0.081/0.083 0.549x0.755 1-1/8 113 1/4 3/8 2-7/8 1-1/8 0.540 0.375 0.275 7/32 1-3/4 1/4 3/8 1 1 0.755 0.140/0.145 0.081/0.083 0.549x0.755 1-1/8 113 1/4 1/2 2-5/8 1-1/8 0.540 0.500 0.390 5/16 1-3/4 1/4 3/8 1 1 0.755 0.140/0.145 0.081/0.083 0.549x0.755 1-1/8 113 3/8 1/4 2-3/8 1-1/8 0.675 0.250 0.170 1/8 1-1/4 3/8 13/32 1-1/8 1-1/8 0.943 0.140/0.145 0.081/0.083 0.737x0.943 1-1/2 116 3/8 3/8 2-7/8 1-1/8 0.675 0.375 0.275 7/32 1-3/4 3/8 13/32 1-1/8 1-1/8 0.943 0.140/0.145 0.081/0.083 0.737x0.943 1-1/2 116 3/8 1/2 2-5/8 1-1/8 0.675 0.500 0.390 13/32 1-1/2 3/8 13/32 1-1/8 1-1/8 0.943 0.140/0.145 0.081/0.083 0.737x0.943 1-1/2 116 3/8 3/4 2-5/8 1-1/8 0.675 0.750 0.600 13/32 1-1/2 3/8 13/32 1-1/8 1-1/8 0.943 0.140/0.145 0.081/0.083 0.737x0.943 1-1/2 116 1/2 1/2 2-5/8 1-1/8 0.840 0.500 0.390 13/32 1-1/2 1/2 17/32 1-1/2 1-1/2 1.068 0.140/0.145 0.081/0.083 0.962x1.068 1-1/2 118 1/2 3/4 3-1/8 1-1/8 0.840 0.750 0.600 1/ 2 2 1/2 17/32 1-1/2 1-1/2 1.068 0.140/0.145 0.081/0.083 0.862x1.066 1-1/2 118 3/4 3/4 3-1/8 1-1/8 1.050 0.750 0.600 19/32 2 3/4 9/16 1-1/2 1-1/2 1.318 0.140/0.145 0.081/0.083 1.112x1.318 1-3/4 122 3/4 1 3-3/4 1-1/8 1.050 1.000 0.840 5/8 2-1/4 3/4 9/16 1-1/2 1-1/2 1.318 0.140/0.145 0.081/0.083 1.112x1.318 1-3/4 122 3/4 1-1/4 3-1/4 1-1/8 1.050 1.250 1.050 5/8 2 3/4 9/16 1-1/2 1-1/2 1.318 0.140/0.145 0.081/0.083 1.112x1.318 1-3/4 122 1 1 3-1/2 1-1/4 1.315 1.000 0.840 23/32 2-1/4 1 21/32 1-11/16 1-11/16 1.568 0.140/0.145 0.081/0.083 1.362x1.568 2 126 1 1-1/4 4-1/2 1-1/4 1.315 1.250 1.050 7/8 3-1/4 1 21/32 1-11/16 1-11/16 1.568 0.140/0.145 0.081/0.083 1.362x1.568 2 126 1 1-1/2 4-3/4 1-1/4 1.315 1.`500 1.260 7/8 3-1/2 1 21/32 1-11/16 1-11/16 1.568 0.140/0.145 0.081/0.083 1.362x1.568 2 126
1-1/4 1-1/4 5-1/4 2 1.660 1.250 1.050 1 3-1/4 1-1/4 1 2-1/16 2-1/16 1.880 0.140/0.145 0.081/0.083 1.674x1.880 2-1/2 131 1-1/4 1-1/2 5-1/4 2 1.660 1.500 1.260 1-1/8 3-1/4 1-1/4 1 2-1/16 2-1/16 1.880 0.140/0.145 0.081/0.083 1.674x1.880 2-1/2 131 1-1/4 2 4-5/8 2 1.660 2.000 1.760 1-3/8 2-5/8 1-1/4 1 2-1/16 2-1/16 1.880 0.140/0.145 0.081/0.083 1.674x1.880 2-1/2 131 1-1/2 3/4 4-3/8 2-1/8 1.900 0.750 0.600 19/32 2-1/4 1-1/2 1-1/16 2-3/8 2-3/8 2.131 0.140/0.145 0.081/0.083 1.925x2.131 2-3/4 135 1-1/2 1 4-1/8 2-1/8 1.900 1.000 0.840 19/32 2 1-1/2 1-1/16 2-3/8 2-3/8 2.131 0.140/0.145 0.081/0.083 1.925x2.131 2-3/4 135 1-1/2 1-1/4 5-1/4 2-1/8 1.900 1.250 1.050 1 3-1/8 1-1/2 1-1/16 2-3/8 2-3/8 2.131 0.140/0.145 0.081/0.083 1.925x2.131 2-3/4 135 1-1/2 1-1/2 5-1/4 2-1/8 1.900 1.500 1.260 1-1/4 3-1/8 1-1/2 1-1/16 2-3/8 2-3/8 2.131 0.140/0.145 0.081/0.083 1.925x2.131 2-3/4 135 1-1/2 2 4-7/8 2-1/8 1.900 2.000 1.760 1-1/4 2-3/4 1-1/2 1-1/16 2-3/8 2-3/8 2.131 0.140/0.145 0.081/0.083 1.925x2.131 2-3/4 135
2 1-1/4 5-3/4 2-1/4 2.375 1.250 1.050 1-3/8 3-1/2 2 1-1/16 2-7/8 2-7/8 2.631 0.140/0.145 0.081/0.083 2.425x2.631 3-1/2 143 2 1-1/2 5-1/2 2-1/4 2.375 1.500 1.260 1-1/4 3-1/4 2 1-1/16 2-7/8 2-7/8 2.631 0.140/0.145 0.081/0.083 2.425x2.631 3-1/2 143 2 2 6-1/4 2-3/4 2.375 2.000 1.750 2 3-1/2 2 1-1/16 2-7/8 2-7/8 2.631 0.140/0.145 0.081/0.083 2.425x2.631 3-1/2 143
"M"
OI
1/16 X 45° CHAMFER
ITEM 6 - FNPT TO SERRATED HOSE CONNECTORS
"H" NPT
A
B
C
"K"
D
E
2.
30° ±5 (TYP)
THE MINIMUM NUMBER OF SERRATIONS IS 4 PER INCH; MAX. 6 PER INCH.
REMOVE BURRS AND/OR SHARP RAISED METAL FROM EDGE OF
SERRATIONS BUT DO NOT FLATTEN SERRATION EDGES.
EXCEPT AS NOTED IN NOTE 2, REMOVE ALL BURRS AND RADIUS ALL
CORNERS 1/64".
2 3
3.
DRAWING NO.
2310-165
SHEET 7 OF 8
REV.
MIN. RADIUS 1/16"
"M"
(SEE NOTES 1 & 2)
"A"
"C"
"B"
"F"
"E"
"D"
2 3
1.
4 5
A
B
C
D
E
DIMENSIONS FOR ITEM 6
SIZE
NPT HOSE
I.D.
A +/-1/8"
B +/-1/16" C D E F H K M
1/4 1/4 2-5/8 3/4 27/64 0.290 0.250 3/32 1/4 1 1-1/2 1/4 3/8 2-5/8 3/4 27/64 0.400 0.375 7/32 1/4 1 1-1/2 1/4 1/2 2-3/4 3/4 27/64 0.535 0.500 5/16 1/4 1 1-1/2 3/8 1/4 2-5/8 3/4 9/16 0.290 0.250 1/8 3/8 1-1/4 1-1/2 3/8 3/8 2-5/8 3/4 9/16 0.400 0.375 7/32 3/8 1-1/4 1-1/2 3/8 1/2 2-3/4 3/4 9/16 0.535 0.500 13/32 3/8 1-1/4 1-1/2 3/8 3/4 2-7/8 3/4 9/16 0.800 0.750 13/32 3/8 1-1/4 1-3/4 1/2 1/2 2-5/8 1 11/16 0.535 0.500 13/32 1/2 1-1/2 1-1/4 1/2 3/4 3-1/8 1 11/16 0.800 0.750 1/2 1/2 1-1/2 1-3/4 3/4 3/4 3-1/8 1 29/32 0.800 0.750 19/32 3/4 1-1/2 1-3/4 3/4 1 3-7/8 1 29/32 1.050 1.000 5/8 3/4 1-1/2 2-1/2 1 1 4 1-1/8 1-1/8 1.050 1.000 23/32 1 1-11/16 2-1/2 1 1-1/4 4-1/2 1-1/8 1-1/8 1.310 1.250 7/8 1 1-11/16 3 1 1-1/2 5 1-1/8 1-1/8 1.560 1.500 7/8 1 1-11/16 3-1/2
1-1/4 1 4-1/8 1-1/4 1-1/2 1.050 1.000 3/4 1-1/4 2-1/16 2-1/2 1-1/4 1-1/4 4-5/8 1-1/4 1-1/2 1.310 1.250 1 1-1/4 2-1/16 3 1-1/4 1-1/2 5-1/8 1-1/4 1-1/2 1.560 1.500 1-1/8 1-1/4 2-1/16 3-1/2 1-1/2 3/4 3-3/8 1-1/4 1-23/32 0.800 0.750 19/32 1-1/2 2-3/8 1-3/4 1-1/2 1-1/4 4-5/8 1-1/4 1-23/32 1.310 1.250 1 1-1/2 2-3/8 3
"K"
"J" (SEE NOTE 1)
"B"
"A" A
"L"
SECT. "A-A"
SIZE 2 END
(REF)
"C"
"D"
SIZE 1 END
"F"
"E"
ITEM 7 - SERRATED HOSE TO SERRATED
HOSE CONNECTORS
THE MINIMUM NUMBER OF SERRATIONS IS 4 PER INCH; MAX. 6 PER
INCH. REMOVE BURRS AND/OR SHARP RAISED METAL FROM EDGE OF
SERRATIONS BUT DO NOT FLATTEN SERRATION EDGES.
EXCEPT AS NOTED IN NOTE 1, REMOVE ALL BURRS AND RADIUS ALL
CORNERS 1/64".
DEPENDING ON THE RELATIVE SIZE OF THE ENDS, ANGLES MAY BE
REVERSED OR NON-EXISTANT.
THE HEX (G) EXCEEDS THE STANDARD SIZES FOR HEX'S.
NOTES
B
C
D
4.
3.
2.
1.
E
30° (SEE NOTE 3)
30°
(SEE NOTE 1)
2 3
"G"
A
"A"
SHEET 8 OF 8
DRAWING NO.
2310-165 REV.
OI
B
D
C
E
"A"
4 5
DIMENSIONS FOR ITEM 7
SIZE
HOSE 1 HOSE 2
A
(REF)
B
MAX
C
+/-1/32 D E F G H J K L M
1/4 1/4 3-3/4 1-3/4 1/2 0.290 0.250 3/32 5/8 1-1/2 1-1/2 0.290 0.250 3/32 1/4 3/8 3-3/4 1-5/8 1/2 0.290 0.250 3/32 5/8 1-1/2 1-1/2 0.400 0.375 7/32 1/4 1/2 3-3/4 1-5/8 1/2 0.290 0.250 3/32 5/8 1-1/2 1-1/2 0.535 0.500 13/32 3/8 3/8 3-3/4 1-3/4 1/2 0.400 0.375 7/32 1/2 1-1/2 1-1/2 0.400 0.375 7/32 3/8 1/2 3-3/4 1-5/8 1/2 0.400 0.375 7/32 3/4 1-1/4 1-1/2 0.535 0.500 13/32 3/8 3/4 4 1-7/8 1/2 0.400 0.375 7/32 7/8 1-1/2 1-3/4 0.800 0.750 15/32 1/2 1/2 3-3/4 1-3/4 1/2 0.535 0.500 13/32 5/8 1-1/2 1-1/2 0.535 0.500 13/32 1/2 3/4 4 1-7/8 1/2 0.535 0.500 13/32 7/8 1-1/2 1-3/4 0.800 0.750 19/32 1/2 1 4-5/8 2-3/8 1/2 0.535 0.500 13/32 1-1/4 1-1/2 2-1/2 1.050 1.000 23/32 1/2 1-1/4 5-1/4 3-1/8 1/2 0.535 0.500 13/32 1-1/2 1-1/2 3 1.310 1.250 7/8 1/2 1-1/2 5-3/4 3-5/8 1/2 0.535 0.500 13/32 1-5/8 1-1/2 3-1/2 1.560 1.500 1-1/4 1/2 2 5-3/4 3-5/8 1/2 0.535 0.500 13/32 2-1/8 1-1/2 3-1/2 2.060 1.995 1-1/2 3/4 3/4 4-3/8 2-1/2 5/8 0.800 0.750 19/32 7/8 1-3/4 1-3/4 0.800 0.750 19/32 3/4 1 5-1/8 2-5/8 5/8 0.800 0.750 19/32 1-1/4 1-3/4 2-1/2 1.050 1.000 23/32 3/4 1-1/4 5-5/8 3-1/8 5/8 0.800 0.750 19/32 1-1/2 1-3/4 3 1.310 1.250 7/8 3/4 1-1/2 6-1/8 3-5/8 5/8 0.800 0.750 19/32 1-5/8 1-3/4 3-1/2 1.560 1.500 1-1/4 3/4 2 6-1/8 3-5/8 5/8 0.800 0.750 19/32 2-1/8 1-3/4 3-1/2 2.060 1.995 1-1/2 1 1 6 2-3/4 3/4 1.050 1.000 23/32 1-1/4 2-1/2 2-1/2 1.050 1.000 23/32 1 1-1/4 6-1/2 3-1/4 3/4 1.050 1.000 23/32 1-1/2 2-1/2 3 1.310 1.250 7/8 1 1-1/2 7 3-3/4 3/4 1.050 1.000 23/32 1-5/8 2-1/2 3 1.560 1.500 1-1/4 1 2 7 3-3/4 3/4 1.050 1.000 23/32 2-1/8 2-1/2 3-1/2 2.060 1.995 1-1/2
1-1/4 1-1/4 7 3-3/4 3/4 1.310 1.250 7/8 1-1/2 3 3 1.310 1.250 7/8 1-1/4 1-1/2 8 3-5/8 3/4 1.310 1.250 7/8 1-5/8 3-1/2 3-1/2 1.560 1.500 1-1/4 1-1/4 2 8 3-5/8 3/4 1.310 1.250 7/8 2-1/8 3-1/2 3-1/2 2.060 1.995 1-1/2 1-1/2 1-1/2 8 3-3/4 3/4 1.560 1.500 1-1/4 1-5/8 3-1/2 3-1/2 1.560 1.500 1-1/4 1-1/2 2 8 3-5/8 3/4 1.560 1.500 1-1/4 2-1/8 3-1/2 3-1/2 2.060 1.995 1-1/2
2 2 8 3-3/4 3/4 2.060 1.995 1-1/2 2-1/8 3-1/2 3-1/2 2.060 1.995 1-1/2
"H"
"M"
File details come from the government source that posted it. Updated .