STATEMENT_OF_WORK.docx

UNITED STATES DEPARTMENT OF JUSTICE

FEDERAL BUREAU OF PRISONS

FCC VICTORVILLE

13777 AIR EXPRESSWAY BLVD.

VICTORVILLE CALIFORNIA, 92394

STATEMENT OF WORK

PART I - GENERAL INFORMATION

A. INTRODUCTION

B. SCOPE

Following are specifications for requested equipment

Purchase, Delivery and Installation of (2) Ea. Double Rack Natural Gas Ovens meeting the following specifications:

· Ovens will be in current production with replacement parts readily available, replacement part pricing will be consistent with current market.

· Ovens will be installed side by side, footprint for both ovens combined must be no larger than 179 inches wide x 96 inches deep (to include hood) x 106 inches high.

· Minimum 275 kBTU/hr, Natural Gas Heated

· 208V, 60Hz, 3-Phase 15 amp Blower

· 120V, 60Hz, 1-Phase 15 amp controls

· Rotating, double rack capacity

· Oven may be split into two halves for movement through 36" openings

· 5" thick compartment insulation; rated at 0" combustible wall clearance, sides and back

· Heavy-duty rack lift and rotate with gear driven rotation system

· Standard digital control

· Integrated hood meeting NFPA 96 and Type I & II construction standards

· Heavy-duty stainless steel interior and exterior

· Automatic, heavy-duty lift and gear-driven rotation system, automatically lifts and lowers with door operation, lift capable of lifting 1 double or 2 single racks

· Heavy-duty door with double-pane viewing window

· Interior door safety release mechanism

· Oven accommodates two single or one double rack, will be set up for double racks

· 100-525 deg F temperature range

· Exhaust heat recovery system

· Racks load at floor level (no ramp)

· Fully integrated hood with single point exhaust connection

· Meets the construction requirements of NFPA 96 & UMC for Type I & II Hoods

· Digital Display Control with programmable recipes

· Selectable Automatic Temperature Setback

· Correctional Package Required

· Ovens must be Energy Star Rated

· (4) Ea. Stainless steel Roll-In Oven Racks, Fully Welded, 20 full size sheet pan capacity, double-side load. Oven Racks shall be constructed with minimum 18 gage stainless steel, welded at each slide to the square tubular stainless steel frame and electro-polished to remove weld slag and discoloration. Casters shall be of hi-temperature design, able to withstand up to 600 degrees and shall include a non-metallic, composite wheel. All fasteners shall be stainless steel. Oven racks shall be reinforced at the bottom frame to minimize rack sway when fully loaded.

· One Year Parts and Labor Warranty

· Freight to 13777 Air Expressway Blvd., Victorville Ca. 92394

Installation shall include:

· Removal of existing equipment. Contractor shall disconnect, and remove the existing ovens and place in a location directed by the Facility Manager.

· Contractors shall supply tools and equipment needed to remove old ovens and install new ovens

· Equipment shall be moved into the facility, uncrated, set in place and leveled.

· Final assembly. Final assembly of equipment.

· Final connection. Final utility connections shall be made on all applicable equipment utilizing existing utilities, ductwork and drain plumbing.

· Contractor shall clean all areas of work and return area back to original condition.

· Start up, operation/leak check shall be performed.

· Post Certification to include verification of installation in accordance with manufacturers’ specifications. Post Certification to be submitted to customer within 30 days of completion of installation.

· One Year Parts and Labor Warranty

· Installation will be performed in a manner which will minimize downtime, work will be performed during normal working hours 7:00 am – 3:30 pm, Monday – Friday.

· The installation will be taking place within the secure confines Federal Correctional Institution #1, therefore all contractors will be required to pass background checks per BOP policy.