Trailer_Description.docx

DESCRIPTION/SPECIFICATIONS/WORK STATEMENT

2024 Dry Van Pup Trailer Purchase – Twin Falls District BLM Quantity: 3 New: Any new trailer that fully meets the specifications may be accepted. Manufacture year for each trailer must be 2024 or newer.

Payload Capacity:

Payload Capacity- 30,000 LBS Evenly Distributed Payload Capacity Gross Vehicle Weight Rating: 37,000 LBS GVWR Dimensions:

Overall Length: Exterior 28’ 0” Width: Exterior 100”-103” Interior 99”-102”wide Overall Height: Exterior 13’6” Interior 109”-111” Trailer Deck Height: The floor of the cargo hold must be a minimum of 45 inches and a maximum of 53 inches when measured from ground level to the floor surface when the trailer is empty

Deck:

Deck Type: Straight Deck with ½ Wedge Front Subframe:

Front Subframe: 3-1/2” Deep Box Beam Design Front Subframe Raise 1 3/8” Flush with top of floor Approach Plate: 8 GA Carbon Sttel Full Width Approach Plate Kingpin Plate: 3 GA High Strength Steel Full Width Kingpin Plate Kingpin Type: AAR Hardnes Cruciform Kingpin Kingpin Location: 36: Kingpin Location Cover Plate: Extruded Aluminum Cover Plate on Lower Front Wall Support Legs:

Support Leg Location: Leg location 69” from Center Line of Kingpin Support Leg Crank Location: Roadside Support Leg Crank Location Support Leg Bracing: Bolt-on Cross Bracing with 7 GA 3-14” Deep High Strength S Channel Support Legs: 50,000 LBS Capacity Support Legs with 10”x10” Ultra Low Profile Cushion Foot Frame, Rails and Crossmemebers:

Bottom Rails: 10-5/8” Deep Heavy Duty Aluminum Bottom Rails Crossmembers From Sub to Legs: 2-3/16” Steel Hate Shaped C-Mems with Continuous Endplate Crossmembers Over Support Legs: 4” Steel I Beam Crossmemebers with Rivet Encd Clips on Centerline over Support Legs Crossmembers Legs to Rear Subframe: 4” Steel I Beam Crossmembers with Rivet End Clips on 12” center line Legs to Rear Sub Crossmembers Over Rear Subframe: 4” Steel I Beam C-Mems with River End Clips 12 Center Line Over Rear Subframe Rear Subframe:

Rear Subframe Type: Fixed I beam Rear Subframe Horizontal Dock Bumper: Base Spec: 7"Horizontal Bumer with 1/4" Reinforce Plate and 2"Additional Dock Lock Clearance x 11"LG @ Centerline of Bumper

Rubber Dock Bumpers: (1) Pair Rubber Dock Bumpers ½” Proud

Vertical and Horizontal Dock Bumper: Base Spec:DOT Vertical with Nonslip 7” Horizontal 22” Max Ground Clearnaces, Meet IIHS-30% ground clearance

Suspension/Axles/Actuation:

Oil Seals: Premium Oil Seals

Air Brake Chambers: 3030 Air Brake Chambers

Air Actuation: One Tank Air Actuation System With Spring Brakes

Slack Adjusters: Automatic Slack Adjusters

Fixed Air Ride Suspension Location: Rear Suspension Center Line 40” to Rear

Hub: 10 Stud Hub Piloted System With Outboard Cast Drums with 16 ½” x 7” Brakes

Wheel Bearing Lubrication: 80W-90 Oil

Air Ride System: 23K Air Ride/Axle System Front Wall:

Front Corner Post: .080 Extruded Aluminum 4 ¾” Radius Fron Corner Posts

Front Wall Posts: (4) 2” 14 GA. High Strength Steel Hat Shaped Front Wall Posts

Front Panels: .040 Aluminum Front Panels

Galdhands and Receptacle Location: Surface MTD Gladhand and Receptacle Offset 27-1/2” to Right Side from Center Line of Trailer

Front Top Rail: Extruded Aluminum Wraparound Front Top Rail

Front Corner Post Protection: 3/8” Mild Steel Bar Front Corner Protector Located at Bottom of Front Corner Post

Side Walls:

Side Panels: Composite Panel Sidewall

Side Posts 3/8” 14 GA High Strength Galvanized Hat Shape 24” Center Line

Roof:

Top Rails: 4 ½” Deep Heavy Duty Extruded Aluminum Top Rails

Roof Skin: .040 One Piece Aluminum Could Roof Skin

Roof Bows 1 1/16” Anti Sag 18 GA Galvanized Steel Hat Shaped Roof Bows 24” Centerline Bonded to Roof Skin

Rear Doors

Rear Door Type: Composite Rear Swinging Doors

Rear Door Panels: ½” Composite Rear Swinging Doors (Painted White Galvanized Steel Panels with Polyethylene Core)

Rear Door Lock Rods: (1) Rear Door Lock Rod Per Door

Rear Door Hinges: (4) Rear Door Hinges per Door

Holdbacks: Chain Link and Hook Type Door Holdbacks

Rear Treadplate: .219 High Strength Steel x 27” Deep Steel Rear Treadplate Integral With Riear Buckplate Rear Door Hing Materials: Aluminum

Floor:

Floor Type: 1 3/8 Hardwood Floor or Aluminum Flooring

Floor Joint Sealant: Caulking Applied Prior to Assembly Between Each Joint

Lining:

Front Wall Lining: .016 Galvanized High Strength Steel Front Wall Lining

Side Wall Lining: Painted While Galvanized Steel with Anti-Snag Sidewall Lining

Wearband: 18 GA x 12” High Corrugated Steel Surface

Wearband on Front: 14 GA x 14” Extra Heavy Duty Corrugated Galvanized Steel

Sidewall Lining Closure: 25 Degree Front Corner Diagonal Sidewall Lining Closure

Electrical System:

Main Harness: Moisture Resistant “Multi-Purpose” 7-Wire Cavle Harness wit Internal Ground and 7 Way Plug

Electrical Receptacle: 7-Way Receptacle Without Circuit Breakers

Clearance Light Quantity: 2-1-2-5 Clearance Light Package

Stop/Tail/Turn Lights: 4” LED Stop/Tail/Turn Lights (2) Per Side with Black Snap in Flange

License Light: LED License Light

Conspicuity Tape: D.O.T. Minimum

Upper Clearance Lights: LED Upper Side Rail Clearance Lights

Lower Clearance Lights: Micro LED PC Rated Light

ABS Warning Light: Micro LED PC Rated Light

Stop/Tail/Turn Light Configuration: Grope Stop/Tail/Turn Lights

Rear Header Clearance Lights: Mico LED PC Rated Grommet Mounted Rear Header Clearance Lights Finish Specifications:

Top Front and Top Side Rail Finish: Natural Aluminum Finish Top, Front and Tip Side Rails

Bottom Side Rail Finish: Natural Aluminum Finish Bottom Side Rails

Front Corner Post Finish: Natural Aluminum Finish Front Corner Post

Front Panel Finish: Pre-Painted White Front Panels

Side Panel Finish: Pre-Painted White Side Panels

Front Subframe Assembly Finish: Front Subframe Fully Flooded Inside with Black Rust Preventative Finish, Top Plate Prime and Painted

Support Leg Finish: Black Rust Preventative Coating on Support Legs

Rear Subframe Finish: Black Rust Preventative Coating on Rear Subframe

Rear Case Finish: Stainless Steel Rear Case

Vertical and Horizontal Dock Bumper Finish: Primed and Painted Black

Roof Exterior Finish: Natural Aluminum Roof Exterior Finish

Rear Door Color: Pre-painted White Rear Doors

Floor Undercoat: Black Sealer/Paint on Bottom of Floor

Miscellaneous:

Mudflap Type: Black Plastic or Rubber Mudflaps

Tires and Wheels:

Wheels: 4-22.5 x 8.25 Steel 10 Hub Pilot

Tires: 4-295/75R 22.5 14 PLY, Load Range G, Speed Rated 75 MPH

Trailer Height: The floor of the cargo hold must be a minimum of 45 inches and a maximum of 53 inches when measured from ground level to the floor surface when the trailer is empty. This is necessary to meet BLM loading dock and loading ramp requirements.

Delivery: Contractor is responsible for all costs associated with loading, transport, and delivery of Dry Vans to the BLM-Shoshone Seed Warehouse, 317 Scenic Hwy 75, Shoshone, Idaho. Contact person will be Michael Shockey at 208-308-4181.