00777 Specifications.pdf

R

Requirements / Specifications: Phase noise analyzer for RF frequencies 1 Version 1.0 (2019) Double-click on for further assistance.

Use this document to detail specifications/requirements for an item and/or ancillary services.

TITLE: Phase noise analyzer for RF frequencies Requesting Lab/Division/Group: PML/Time and Frequency/Optical Frequency Measurements Group

General Statement of Need To support our research activities developing ultrastable RF and microwave, and optical sources, we require a phase noise test set capable of measuring RF sinewave sources with state-of-the-art phase noise.

Items and/or Ancillary Services

Item 1: Phase noise analyzer Quantity: 1 Specifications: Measurement capabilities: Phase noise, Amplitude noise, Allan deviation

Either front panel or software control. All necessary control software must be included.

Device under test (DUT) input frequency range: 1 MHz to 200 MHz

Input power range: at least -5 dBm to +15 dBm

Input impedance: 50 ohms

Cross spectrum measurement capability on phase noise and amplitude noise

Dual reference oscillator input capability - must be able to measure cross-spectrum against 2 user-supplied reference oscillators without PLL feedback or voltage tuning on references, and without the reference oscillator frequencies matching each other or the DUT. For example, the DUT frequency may be 20 MHz whereas reference oscillator 1 is 10 MHz and reference oscillator 2 is 5 MHz.

Phase noise measurement offset frequency range: For DUT frequency > 2 MHz, at least 0.01 Hz to 1 MHz

Instrument-limited noise floor on 10 MHz carrier, large number of averages assumed:

1 Hz offset: < -130 dBc/Hz 100 Hz offset: < -160 dBc/Hz 10 kHz offset: < -180 dBc/Hz 1 MHz offset: < -180 dBc/Hz

Instrument-limited Allan deviation floor: < 10^-14 at 1 second

Separately Priced Options and Services:

Item 2: [List minimum specifications.

Requirements / Specifications: Phase noise analyzer for RF frequencies 2

Quantity: [Enter quantity here.] Specifications: [Enter quantity here.]

[List any other item(s) or service requirements here using the same format above.]

Service Requirements / Item Specifications

Section Requirements/Specifications Planning Considerations ☒ N/A

☐ List any visits required to allow potential vendors to see site specific constraints.

[Explain requirement here] ☐ US citizen required on-site (foreign nationals require preregistration 30 days prior) ☐ Vendor rep on-site more than three days ☐ Other considerations: [List other considerations to ensure an accurate quote]

Shipping & Delivery ☐ N/A

[Enter shipping and delivery information by item here.] Shipping criteria:

☐ Partial delivery acceptable ☐ Direct delivery to building required [Explain need for requirement here] Building has: ☐ Loading dock ☐ Containerization preference: [Choose container] Other requirements: [List any other requirements here] Delivery date criteria:

☒ Delivery of goods, installation, and training shall be completed no later than:

No longer than 8 weeks after receipt of order ☐ Deliver no earlier than: [Insert date here] ☐ Other: [List other shipping, delivery, or specil requirements]

Electronic Media ☐ N/A

Control software, if any, must be included ☒ Software ☐ Electronic manuals ☐ License Key ☐ Other: [List any other Electronic Media requirements here] [Enter email address for software delivery here]

Installation ☒ N/A

[Enter installation requirements by item here.] ☐ Vendor technician on site ☐ Rigging ☐ Uncrating / Unpackaging ☐ Removal of packaging material ☐ Equipment set up ☐ Start-up services ☐ Turn key installation ☐ Other [Enter details here.] Note: When installation is required, TPOC or COR shall be the coordination point.

Facility / Utility Considerations

[List site specific utility considerations by item here.] ☐ OFPM Work Order Number(s)

Requirements / Specifications: Phase noise analyzer for RF frequencies 3

☒ N/A [List any Work Order Number(s) here] ☐ Power available Voltage: [Enter voltage here] (V) Max Current: [Enter max current draw here] (A) Phase: [Choose phase] Frequency: [Typically 60Hz] (Hz) NEMA Plug Type: [Enter plug type here] (i.e.: NEMA L5-20P) Environment: [Choose environment] Other power consideration: [List any other power considerations here] ☐ Utility connections: [List relevant available utilities, pressure(s), and flowrate(s)] ☐ Other considerations: [List other considerations to ensure an accurate quote]

Warranty ☒ N/A

Base Manufacturer Warranty is acceptable [If you require an Extended Manufacturer Warranty, describe the warranty requirements per item here.] What is included?

☐ Labor ☐ Parts ☐ Travel ☐ Cost and liability for returns ☐ Other: [Enter other requirements here] ☐ Warranty length: [Enter warranty length here] Period Length:[Ex. month, 6 month, year etc.]

Training ☒ N/A

[Training requirements (who, when, what, where) here. If on-site, is travel necessary?] ☐ On-site ☐ Off-site location: [Enter location(s) here] ☐ Number of trainees: [Enter number of trainees here] Scope of training:

☐ Operations ☐ Maintenance ☐ Troubleshooting ☐ Safety ☐ Other: [Enter other scope requirements here] ☐ Training materials to be provided: [Describe requirement here] ☐ Other: [Enter other training requirements here] Note: When training is required, TPOC or COR shall be the coordination point.

Inspection and Acceptance ☐ N/A

[Enter inspection requirements per item here] ☒ Planned government acceptance testing (7 business days) ☐ Gov’t acceptance expected to take longer than 7 business days: [Duration] ☐ Inspection and acceptance plan: [Explain here] ☐ Other: [Enter other requirements here]

Maintenance [Describe your maintenance requirements per item here] Period Length: [Ex. month, 6 month, year etc.]

Requirements / Specifications: Phase noise analyzer for RF frequencies 4

☒ N/A What is included?

☐ Labor ☐ Spare parts ☐ Consumables ☐ Travel ☐ Cost and liability for returns ☐ Software updates ☐ Manuals ☐ Service plan length: [Enter service plan length here] ☐ Other: [Enter other requirements here] ☐ Requirements: [Enter requirements here] (i.e.: onsite within 72 hours, etc.)

☐ Option Period 1 ☐ Option Period 2 ☐ Option Period 3 ☐ Option Period 4

Government Furnished Material / Equipment ☒ N/A

[List any government furnished material/equipment per item here] ☐ Samples for testing ☐ Government equipment which will leave gov't site (TPOC must coordinate with division property custodian) Serial Number: [Enter Serial Number here] Description: [Enter description here] NIST property number: [Enter NIST property number here] ☐ Other: [Enter other details here]

Travel ☒ N/A

[Describe any travel requirements per item here] ☐ Explain: [Explain here] ☐ Other: [Enter other requirements here] Vendor: To the maximum extent possible, include as part of appropriate sections above (maintenance, repair, etc.). Otherwise, it will be a separate line item, reimbursable per the Federal Travel Regulation.

Provide suggestions to improve this form by clicking here.

https://oaam.nist.gov/OAAMAcquisitions/FormFeedback/default.aspx